Yamaha RX-V465 Black: BASIC OPERATION

BASIC OPERATION

Playback

INTRODUCTION

Basic procedure

Using the SCENE function

This unit has a SCENE function that allows you to change

1 Turn on external components (TV, DVD

input sources and sound field programs with one key. Four

player, etc.) connected to this unit.

scenes are available for different usages, such as playing

movies or music. The following input sources and sound

2 Press NINPUT l / h (or gInput

field programs are provided as the initial factory settings.

selection keys) to select an input source.

PREPARATION

The name of the selected input source is displayed for

Input source Sound field program

a few seconds.

BD/DVD HDMI 1 Straight

Input source name

TV AV 1 Straight

VOL.

CD AV 3 Straight

RADIO TUNER 7ch Enhancer

AV1

OPERATION

y

• When this unit is on standby, you can turn on this unit by pressing the

BASIC

3 Play the external component that you have

SCENE key.

selected as the source input, or select a radio

Selecting a SCENE

station on the tuner.

Refer to the operating instructions of the external

Press ISCENE (or kSCENE).

component for details on playback. For selecting

radio stations or playback of an iPod or Bluetooth

OPERATION

component using this unit, see the following.

ADVANCED

Registering input source/sound field

• FM/AM radio tuning (see page 28)

program

• Bluetooth component playback (see page 34)

• iPod playback (see page 32)

Select the desired input source/sound field

program, and pressing down ISCENE (or

4 Turn the PVOLUME control to adjust the

kSCENE) until “SET Complete” appears on the

volume (or press oVOLUME +/–).

front panel display.

INFORMATION APPENDIX

ADDITIONAL

Volume

Switching remotely controlled external

VOL.

components linked to scene selections

SW

LR

C

SL SR

Volume-18.5dB

You can operate an external component with the remote

control of this unit by setting a remote control code for the

Note

external component for each input source. Setting remote

When you play back a DTS-CD, noise may be output in some

control codes for desired input sources allows you to

conditions, which may cause a speaker malfunction. Make sure

switch between external components linked to scene

that the volume is set to low before starting playback. If noise is

selections.

output, do the following.

1 Register the remote control code of an

1) When only noise is output

external component to the desired input

If a DTS bitstream signal is not properly input to this unit,

only noise is output. Connect the playback component to this

source (see page 46).

unit by digital connection and play back the DTS-CD. If the

Note

condition is not improved, the problem may results from the

• Remote control codes cannot be registered to a TUNER input.

playback component. Consult the manufacturer of the

playback component.

2) When noise is output during playback or skip operation

Before playing back the DTS-CD, display the option menu

English

after selecting the input source and set “Decoder Mode” to

“DTS” (see page 35).

21 En

Playback

2 Press gInput selection keys on the

Enjoying pure hi-fi sound

remote control for the input source whose

Use Direct mode to enjoy the pure high fidelity sound of

remote control code was registered in step 1

the selected source. When Direct mode is activated, this

for about 3 seconds while pressing down

unit plays back the selected source with the least circuitry.

kSCENE key whose assignment you want

to change.

Press MDIRECT (or jDIRECT) to turn the

The external component can now be controlled

Direct mode on or off.

remotely just by selecting a scene.

The following features are disabled in Direct mode.

– sound field program, tone control

Muting audio output temporarily

– display and operation of the option menu and setup

(MUTE)

menu

y

1 Press qMUTE on the remote control to mute

• While direct mode is on, the front panel display becomes dim. When

setting it back off, the brightness of the front panel display returns to the

the audio output.

previous setting.

The MUTE indicator on the front panel display

flashes while audio output is muted.

Using the sleep timer

2 Press qMUTE again to resume audio

The sleep timer is useful if you want to go to sleep while

this unit is playing or recording a source.

output.

Press eSLEEP repeatedly to set the amount of

Adjusting high/low frequency sound

time.

(tone control)

Each time you press eSLEEP, the front panel display

changes as shown below.

You can adjust the balance of the high frequency range

(Treble) and low frequency range (Bass) of sounds output

Sleep 120min. Sleep 90min.

from the front left and right speakers to obtain desired

tone.

Sleep 60min.Sleep 30min.Sleep Off

y

When the sleep timer is set, the SLEEP indicator on the

• The tone control of the speakers or headphones can be set separately. Set

front panel display lights up.

the headphone tone control with the headphones connected.

Press eSLEEP on the remote control repeatedly until

1 Press JTONE CONTROL on the front panel

“Sleep Off” appears on the front panel display.

repeatedly to select “Treble” or “Bass.”

Using your headphones

The current setting is displayed on the front panel

display.

Plug your headphones in the BPHONES jack on

the front panel.

When you select a sound field program while using the

Treble

0.0dB

headphones, the mode is automatically set to SILENT

CINEMA mode.

2 Adjust the frequency range using

KPROGRAM l / h.

Notes

Control range: –10.0 dB to +10.0 dB

• When you connect headphones, no signals are output at the speaker

terminals.

The display returns the previous screen soon after you

• When multi-channel signals are processed, sounds in all channels are

release the key.

divided to left and right channels.

Notes

• The tone control settings are not effective during playback in direct

mode.

• If you set the balance extremely off, sounds may not match those from

other channels well.

22 En

Playback

Displaying input signal information

Changing information on the front

panel display

You can display information on audio/video signals input

INTRODUCTION

to this unit for each input source.

Information displayed on the front panel display can be

changed by pressing CINFO (or iINFO).

1 Select the desired input source, and press

The following information can be displayed according to

mOPTION.

the input source.

The option menu for the selected input source is

For example, if you select HDMI1 input and display “DSP

displayed (see page 35).

Program,” the following screen appears on the front panel

display.

2 Press nCursor k / n to select “Signal Info,”

PREPARATION

and press nENTER.

Input source

Information on input signals is displayed. See

page 36 on messages displayed on the front panel

display.

Straight

3 Press nCursor k / n to select the desired

Sound field program (DSP program)

item.

The following information is displayed for each input

source.

OPERATION

BASIC

HDMI1-4: Input, DSP Program, Audio Decoder

DolbyD

AV1-6: Input, DSP Program, Audio Decoder

AUDIO1-2: Input, DSP Program, Audio Decoder

Note

V-AUX: Input, DSP Program, Audio Decoder

• If an HDMI related error occurs, press nCursor to display an

FM/AM: Frequency, Program Service, Program

error message.

Type, Radio Text, Clock Time, DSP

4 To end the information display, press

Program, Audio Decoder

OPERATION

ADVANCED

iPod (Simple remote mode): Input, DSP Program, Audio Decoder

mOPTION.

iPod (Menu browse mode): (in PlayInfo displayed) Artist, Album,

Song, DSP Program, Audio Decoder

(in Play menu displayed) List

Bluetooth: Input, DSP Program, Audio Decoder

INFORMATION APPENDIX

ADDITIONAL

English

23 En

Radio Data System tuning (Europe and Russia models only)

Radio Data System is a data transmission system used by FM stations in many countries. This unit can receive various

Radio Data System data such as “Program Service,” “Program Type,” “Radio Text,” “Clock Time,” and “EON”

(enhanced other networks) when receiving Radio Data System broadcasting stations.

Displaying the Radio Data System

Selecting the Radio Data System

information

program type (PTY Seek mode)

Use this feature to display the 4 types of the Radio Data

Use this feature to select the desired radio program by

System information: “Program Service,” “Program Type,”

program type from the all preset Radio Data System

“Radio Text,” “Clock Time.”

broadcasting stations.

y

1 Tune into the desired Radio Data System

• You must preset stations prior to using PTY Seek. When “No Presets” or

broadcasting station.

“No Presets in Memory” is displayed, it means that no stations are

registered. See page 29 and register stations.

y

• We recommend that you use the automatic preset tuning to tune

1 Press gTUNER on the remote control to

into the Radio Data System broadcasting stations (see page 28).

select “TUNER” as the input source.

• You can also use PTY Seek mode to tune into the desired Radio

Data System broadcasting station from the preset ones.

2 Press mOPTION on the remote control.

2 Press cINFO on the front panel (or iINFO

The tuner option menu appears. See page 35 for

on the remote control) repeatedly until the

details of the option menu.

desired information is displayed.

Information on the display changes as you press the

3 Press nCursor k / n on the remote control

key. The kind of information is displayed for a while

to select “PTY Seek,” and press nENTER.

and then the information is displayed.

ProgramService ProgramType RadioText

PTY:SPORT

Frequency display

ClockTime

4 Press nCursor l / h on the remote control

DSPProgramAudioDecoder

to select a program type for search.

Contents of information are as follows.

You can select a program type from the following.

Choice Function

Program type Description

Program

Displays the name of the Radio Data

NEWS News

Service

System program currently being

received.

AFFAIRS Current affairs

Program Type Displays the type of the Radio Data

INFO General information

System program currently being

SPORT Sports

received.

EDUCATE Education

Radio Text Displays the information on the Radio

Data System program currently being

DRAMA Drama

received.

CULTURE Culture

Clock Time Displays the current time.

SCIENCE Science

DSP Program Displays the currently selected sound

VARIED Light entertainment

field program.

POP M Popular music

Audio Decoder Displays the currently selected

surround decoder.

ROCK M Rock music

M.O.R. M Middle-of-the-road music

(easylistening)

LIGHT M Light classics

CLASSICS Serious classics

OTHER M Other music

30 En

Radio Data System tuning (Europe and Russia models only)

5 To search a station, press nCursor k / n on

5 After selecting a program type, press

the remote control.

mOPTION to end the option menu.

If you press nCursor n, this unit searches

When an affiliate station starts broadcasting the

INTRODUCTION

downward from the current frequency. If you press

selected program, this unit automatically tunes in to

nCursor k, it searches upward from the current

that station. When the program ends, it automatically

preset station.

switches back to the previous station.

When a station is detected, the search stops. If the

The EON is switches off in the following cases:

station is not the desired one, Press the same key to

– when the EON is activated once

continue the search.

– when this unit is set to standby before EON is

To end the search, press mOPTION.

activated

– when another station is selected before EON is

PREPARATION

Note

activated

• If “Not found” is displayed, no station applicable for the selected

program type is detected.

y

• To cancel the EON, do steps 1 through 5 again and select

“EON:OFF.”

Using the enhanced other networks

(EON) data service

Use this feature to receive the EON (enhanced other

networks) data service of the Radio Data System station

OPERATION

network. Once you select one of the 4 Radio Data System

BASIC

program types (NEWS, AFFAIRS, INFO or SPORT), this

unit automatically searches for all the available preset

stations that are scheduled to broadcast the EON data

service of the selected program type for a certain duration

of time. When the scheduled EON data service starts, this

unit automatically switches to the local station

broadcasting the EON data service and then switches back

OPERATION

ADVANCED

to the national station once the EON data service ends.

1 Tune into the desired Radio Data System

broadcasting station.

2 Press mOPTION on the remote control.

The tuner option menu appears. For details on the

INFORMATION APPENDIX

ADDITIONAL

option menu, see page 35.

3 Press nCursor k / n on the remote control

to select “EON,” and press nENTER.

“EON:OFF” appears on the front panel display.

Current frequency

EON:OFF

y

• When “No Presets” or “No Presets in Memory” is displayed it

means that no stations are registered. See page 29 and register

stations.

• If the affiliate station of the selected preset station or the EON data

service is not available, “Not Available” appears.

4 Press nCursor l / h to select a program

type.

English

NEWS AFFAIRS INFO

OFF

SPORT

31 En

Using iPod™

Once you have stationed your iPod in a Yamaha iPod universal dock (such as the YDS-11, sold separately) connected to

the DOCK terminal on the rear panel of this unit (see page 16), you can enjoy playback of your iPod using the supplied

remote control. You can also use the Compressed Music Enhancer mode of this unit to improve the sound quality of the

compression artifacts (such as MP3 format) stored on your iPod (see page 24).

Notes

• iPod touch, iPod (Click and Wheel including iPod classic), iPod nano, and iPod mini are supported.

• Some features may not be compatible depending on the model or the software version of your iPod.

• Some features may not be available depending on the model of Yamaha iPod universal dock. The following sections describe the procedure when using

the YDS-11.

y

• Once the connection between your iPod and this unit is complete, “iPod connected” appears on the front panel display.

• For a complete list of status messages that appear on the front panel display, see the “iPod” section on page 52.

1 Change the input source to “iPod (DOCK)”

Controlling iPod™

using NINPUT l / h (or gDOCK).

You can control your iPod when you set it in the iPod

Press pDISPLAY on the remote control to change

universal dock and switch the input source to DOCK. The

between menu browse mode and simple remote

operations of your iPod can be done with the aid of the

mode, as required.

front panel display (menu browse mode) or without it

When you select menu browse mode, the front panel

(simple remote mode).

display changes as follows.

When you connect your iPod to this unit, you can perform

the following operations with the remote control.

VOL.

SW

LR

C

Key Function

SL SR

Music

ENTER Subsequent menu

k Menu up

2 Press nCursor k / n / l / h to select a

menu item and then nENTER to start

n

n Menu down

playback.

l Previous menu

Menu items of “Music”

h Subsequent menu

Playlists, Artists, Albums, Songs, Genres, Composers

w Search backward (Press and hold)

• Playlists > Songs

• Artists > Albums > Songs

f Search forward (Press and hold)

• Albums > Songs

a Skip forward

• Songs

• Genres > Artists > Albums > Songs

b Skip backward

r

• Composers > Albums > Songs

s Stop

Menu items of “Videos”

Pause (Menu browse mode)

e

Menu items vary depending on the files stored on

Play/Pause (Simple remote mode)

your iPod.

Play (Menu browse mode)

p

y

Play/Pause (Simple remote mode)

• You can change information screens on the front panel display

using CINFO (or iINFO) (see page 23). Items displayed on the

Switch between Menu browse mode and

front panel display vary depending on mode that is currently

p DISPLAY

Simple remote mode

selected.

y

• You can directly operate your iPod while it is connected to this unit.

32 En

Using iPod™

Shuffle/repeat playback

You can use a special playback function such as shuffle

playback and repeat playback by setting the option menu.

INTRODUCTION

1 Press pDISPLAY to switch to menu browse

mode while “DOCK” is selected as the input

source.

The option menu can be displayed only in menu

browse mode. Press pDISPLAY to switch to menu

browse mode before starting shuffle or repeat

PREPARATION

playback.

2 Press mOPTION.

The option menu is displayed.

3 Press nCursor k / n to select the desired

playback function, Shuffle or Repeat, then

press nENTER.

The following playback styles are available

OPERATION

depending on the playback function selected.

BASIC

Shuffle: Plays back songs or albums in random

order (Choices: Off, Songs, Albums).

• Select “Off” if you do not want to play back in

random order.

• Select “Songs” to play back songs in random order.

OPERATION

• Select “Albums” to play back albums in random

ADVANCED

order.

Repeat: Plays back songs or albums repeatedly

(Choices: Off, One, All).

• Select “Off” if you do not want to play back

repeatedly.

• Select “One” to repeat each song.

INFORMATION APPENDIX

ADDITIONAL

• Select “All” to repeat all songs.

4 Select the desired style using nCursor l /

h.

The style is selected. Playback starts with the

function selected in step 3.

To return to the previous screen, press nRETURN.

To return to the previous playback function, redo the

above steps.

English

33 En

Using Bluetooth™ components

You can connect a Yamaha Bluetooth wireless audio receiver (such as YBA-10, sold separately) to the DOCK terminal of

this unit and enjoy the music contents stored in your Bluetooth component (such as a portable music player) without

wiring between this unit and the Bluetooth component. You need to perform “Pairing” the connected Bluetooth wireless

audio receiver and your Bluetooth component in advance.

Note

• This unit supports A2DP (Advanced Audio Distribution Profile) of the Bluetooth profile.

6 Select the Bluetooth wireless audio receiver

Pairing the Bluetooth™ wireless audio

from the Bluetooth device list, and enter a

receiver and your Bluetooth™

path key “0000” into the Bluetooth

component

component.

“Pairing” refers to the operation of registering a Bluetooth

When pairing is complete, “Completed” appears on

component for Bluetooth communications. Pairing must

the front panel display.

be performed when using a Bluetooth component with the

y

Bluetooth wireless audio receiver connected to this unit

• The Yamaha Bluetooth wireless audio receiver can be paired with up to

eight Bluetooth components. When pairing is conducted successfully

for the first time or if the pairing data has been deleted.

with a ninth component and the pairing data is registered, the pairing data

for the least recently used other component is cleared.

y

• You only need the pairing operation for the first time that you use the

Bluetooth component with the Bluetooth wireless audio receiver.

Playback of the Bluetooth™

• Pairing requires operations on this unit and on the other component with

which Bluetooth communications are to be established. If necessary,

component

refer to the other component’s operating instructions.

■ Pairing the Bluetooth wireless audio receiver

1 Change the input source to “DOCK” using

and your Bluetooth component

NINPUT l / h (or gDOCK).

To ensure security, a time limit of 8 minutes is set for

2 Press mOPTION.

the pairing operation. You are recommended to read

and fully understand all the instructions before starting.

3 Press nCursor n repeatedly to select

“Connect” and press nENTER.

1 Change the input source to “DOCK” using

After you execute “Connect,” communication with

the Bluetooth component is established. When the

NINPUT l / h (or gDOCK).

connected Bluetooth wireless audio receiver

2 Turn on the Bluetooth component you want

recognizes the Bluetooth component, “BT

to pair with and set it to pairing mode.

Connected” appears on the front panel display.

For details on operation of the Bluetooth component,

y

• When you press nENTER on the remote control, the connected

refer to its operating instructions.

Bluetooth wireless audio receiver searches and connects to the last

connected Bluetooth component. If the Bluetooth wireless audio

3 Press mOPTION.

receiver cannot find the Bluetooth component, “Not found”

appears on the front panel display.

The option menu for DOCK input appears on the

• To disconnect the Bluetooth wireless audio receiver from the

front panel display.

Bluetooth component, display the option menu again, select

“Disconnect,” and press nENTER.

4 Press nCursor n to select “Pairing” and

4 Start playback of the Bluetooth component.

press nENTER.

“Searching” appears on the front panel display and

the pairing operation starts.

y

• To cancel pairing, press nRETURN.

• You can also start pairing operation by pressing and holding

DMEMORY on the front panel.

5 Make sure the Bluetooth component

recognizes the Bluetooth wireless audio

receiver.

If the Bluetooth have recognized the Bluetooth

wireless audio receiver, “YBA-10 YAMAHA,” for

instance, is displayed in the Bluetooth device list.

34 En