JVC KD-G507: RADIO OPERATIONS

RADIO OPERATIONS

ENGLISH

To stop searching before a station is

Listening to the radio

received, press the same button you have

pressed for searching.

You can use either automatic searching or manual

searching to tune in to a particular station.

Note:

FM1 and FM2: 87.5 MHz – 108.0 MHz

Searching for a station automatically:

FM3: 65.00 MHz – 74.00 MHz

Auto search

1

Select the band (FM1 – 3, AM).

Searching for a station manually:

Each time you press the

Manual search

button, the band changes as

follows:

1

Select the band (FM1 – 3, AM).

FM1 FM2 FM3 AM

Each time you press the

button, the band changes as

follows:

Selected band appears.

FM1 FM2 FM3 AM

Note:

This receiver has three FM bands (FM1, FM2,

Lights up when receiving an FM stereo

FM3). You can use any one of them to listen to

broadcast with sufficient signal strength.

an FM broadcast.

2

Press and hold ¢ or 4

Note:

until “M” (manual) starts flashing on

This receiver has three FM bands (FM1, FM2,

the display.

FM3). You can use any one of them to listen to

an FM broadcast.

2

Start searching for a station.

To search for stations of

higher frequencies

To search for stations of lower frequencies

When a station is received, searching stops.

8

EN08-10_KD-G507[EE]f.p65 11/21/03, 2:44 PM8

3

Tune in to a station you want while

Storing stations in memory

“M” (manual) is still flashing.

You can use one of the following two methods to

To tune in to stations of

store broadcasting stations in memory.

higher frequencies

• Automatic preset of FM stations: SSM (Strong-

ENGLISH

station Sequential Memory)

• Manual preset of both FM and AM stations

To tune in to stations of lower frequencies

FM station automatic preset: SSM

• If you release your finger from the button,

You can preset 6 local FM stations in each FM

the manual mode will automatically turns

band (FM1, FM2, and FM3).

off after 5 seconds.

• If you hold down the button, the frequency

1

Select the FM band (FM1 – 3) you

keeps changing—in 50 kHz intervals

want to store FM stations into.

(87.5 MHz – 108.0 MHz for FM 1 and

Each time you press the

FM 2), in 30 kHz intervals (65.00 MHz –

button, the band changes as

74.00 MHz for FM 3) and 9 kHz for AM

follows:

—MW/LW until you release the button.

FM1 FM2 FM3 AM

When an FM stereo broadcast is hard to

receive:

2

Press MODE to enter the functions

1 Press MODE to enter the

mode.

functions mode while listening

to an FM stereo broadcast.

2 Press MO (monaural), while

“MODE” is still flashing on the

display, so that “MONO”

appears on the display.

3

Press and hold SSM for about

Each time you press the button,

2 seconds.

monaural mode turns on and off

alternately.

MO (monaural) indicator

When the MO indicator is lit on the display, the

“SSM” flashes, then disappears

sound you hear becomes monaural but the

when automatic preset is over.

reception will be improved.

Local FM stations with the strongest signals are

searched and stored automatically in the band

number you have selected (FM1, FM2, or FM3).

These stations are preset in the number buttons

—No.1 (lowest frequency) to No.6 (highest

frequency).

When automatic preset is over, the station stored

in number button 1 will be automatically tuned in.

9

EN08-10_KD-G507[EE]f.p65 11/21/03, 3:11 PM9