Sony CDX-GT50UI: RDS USB playback Error displays/Messages

Automatic tuning is not possible.

CHECKING

• Setting of the local seek mode is not correct.

The unit is confirming the connection of a USB device.

t Tuning stops too frequently:

t Wait until confirming the connection is finished.

Set “LOCAL-ON” (page 14).

1

ERROR*

t Tuning does not stop at a station:

2

• The disc is dirty or inserted upside down.*

Set “MONO-ON” (page 14).

t Clean or insert the disc correctly.

• The broadcast signal is too weak.

• A blank disc has been inserted.

t Perform manual tuning.

• The disc cannot play due to a problem.

During FM reception, the “ST” indication

t Insert another disc.

flashes.

• USB device was not automatically recognized.

• Tune in the frequency accurately.

t Reconnect it again.

• The broadcast signal is too weak.

FAILURE

t Set “MONO-ON” (page 14).

The connection of speakers/amplifiers is incorrect.

An FM program broadcast in stereo is heard in

t See the installation guide manual of this model to

check the connection.

monaural.

The unit is in monaural reception mode.

HUB NO SUPRT

tSet “MONO-OFF” (page 14).

USB hub or devices that have a hub function are not

supported on this unit.

LOAD

RDS

The changer is loading the disc.

The SEEK starts after a few seconds of

t Wait until loading is complete.

listening.

L. SEEK +/–

The station is non-TP or has weak signal.

The local seek mode is on during automatic tuning.

tDeactivate TA (page 9).

NO AF

No traffic announcements.

There is no alternative frequency for the current

• Activate TA (page 9).

station.

• The station does not broadcast any traffic

t Press (SEEK) –/+ while the program service name

announcements despite being TP.

is flashing. The unit starts searching for another

t Tune in another station.

frequency with the same PI (Program

PTY displays “- - - - - - - -.”

Identification) data (“PI SEEK” appears).

• The current station is not an RDS station.

NO DEV (No Device)

• RDS data has not been received.

(SOURCE) is selected without a USB device

• The station does not specify the program type.

connected. A USB device or a USB cable has been

disconnected during playback.

t Be sure to connect a USB device and USB cable.

USB playback

NO DISC

You cannot play back items via a USB hub.

The disc is not inserted in the CD/MD changer.

This unit cannot recognize USB devices via a USB

t Insert discs in the changer.

hub, and is not compatible with a device that has a hub

NO INFO

function.

Text information is not written in the MP3/WMA/

Cannot play back items.

AAC files or ATRAC CD.

• Play back music files are protected by Digital Rights

NO IPOD

Management (DRM) technology (page 16).

No iPod connected.

• Play back items on non-Mass Storage Class USB

t Connect iPod to dock connector.

devices only.

If “NO IPOD” appears while connecting the iPod to

• If a USB device does not work, reconnect it.

the dock connector, disconnect the iPod from the dock

A beep sounds.

connector, then reconnect.

During playback, the USB device has been

NO MAG

disconnected.

The disc magazine is not inserted in the CD changer.

tBefore disconnecting a USB device, make sure to

t Insert the magazine in the changer.

stop playback first for data protection.

NO MUSIC

The sound is intermittent.

The disc/USB device does not contain a music file.

The sound may be intermittent at a high-bit-rate of

t Insert a music CD in this unit or MP3 playable

more than 320 kbps.

changer.

t Connect a USB device with a music file in it.

NO NAME

Error displays/Messages

A disc/album/group/track/artist/playlist name is not

written in the track.

1

BLANK*

NO TP

2

Tracks have not been recorded on the MD.*

The unit will continue searching for available TP stations.

tPlay an MD with recorded tracks.

continue to next page t

21