Ariston Aqualtis AQ7L 093 X: инструкция

Instructions for

WASHING MACHINE

installation and use

Contents

EN

Installation, 2-3

EN

Unpacking and levelling

ES

PT

Connecting the electricity and water supplies

Technical data

English,1

Español,13

Português,25

Description of the machine, 4-5

Control panel

CIS

Running a wash cycle, 6

Русский,37

Wash cycles and options, 7

Table of wash cycles

Wash options

CIS

Detergents and laundry, 8

Detergent

Preparing the laundry

Washing recommendations

Load balancing system

Precautions and advice, 9

AQUALTIS

General safety

Disposal

Opening the porthole door manually

AQ7L 093 X

Care and maintenance, 10

Cutting off the water and electricity supplies

Cleaning the machine

Cleaning the detergent dispenser drawer

Caring for your appliance drum

Cleaning the pump

Checking the water inlet hose

Trouble shooting, 11

Assistance, 12

1

Installation

! This instruction manual should be kept in a safe place

! If the appliance is levelled correctly, it will be more stable

EN

for future reference. If the washing machine is sold, given

and much less likely to cause vibrations and noise while it

away or moved, please ensure the manual is kept with

is operating, particularly during the spin cycle.

the machine, so that the new owner may benefit from the

! If it is placed on carpet or a rug, adjust the feet in such a

advice contained within it.

way as to allow a sufficient ventilation space underneath

! Read these instructions carefully: they contain vital

the washing machine.

information relating to the safe installation and operation of

the appliance.

Connecting the electricity and water

! Inside the pack containing this manual, you will also find

supplies

the guarantee and all the details necessary for installation.

Connecting the water inlet hose

Unpacking and levelling

! Before connecting the inlet hose to the water supply, run

Unpacking

the water until it is perfectly clear.

1. Once you have removed all the packaging from the

1. Connect the inlet hose

washing machine, make sure it has not been damaged

to the machine by screwing

during transportation.

it onto the cold water inlet

If it has been damaged, contact the retailer and do not

of the appliance, which is

proceed any further with the installation process.

situated on the top right-

hand side of the rear part of

2. Remove the 4 protective

the appliance (see figure).

screws (used during

transportation) and the

corresponding spacer,

located on the rear part of

the appliance (see figure).

2. Connect the inlet hose

by screwing it to a cold

water tab using a 3/4 gas

threaded connection (see

figure).

3. Close off the holes using the plastic plugs supplied in the

pack.

4. Keep all the parts in a safe place; they will be needed

again if the washing machine is moved to another location,

to prevent the inside of the appliance being damaged.

! Packaging materials should not be used as toys for

children.

3. Make sure that the hose is not folded over or bent.

Levelling

! The water pressure at the tap must fall within the values

1. Place the washing machine on a flat sturdy floor, without

indicated in the Technical data table (see next page).

resting it up against walls or cabinets.

! If the inlet hose is not long enough, contact a specialised

2. If the floor is uneven, the

shop or an authorised technician.

front feet of the machine

may be adjusted until

! Never use second-hand or old inlet hoses; use the

it reaches a horizontal

products supplied with the machine.

position (the angle of

inclination must not exceed

2 degrees).

22

EN

Technical data

Model

AQ7L 093 X

width 59.5 cm

Dimensions

height 85 cm

depth 64,5 cm

Capacity

from 1 to 7 kg

Electrical

please refer to the technical data plate

connections

fixed to the machine

maximum pressure 1 MPa (10 bar)

Water connections

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 62 litres

Spin speed

up to 1000 rotations per minute

Test Program-

programme

;

mes according to

temperature 60°C and 40°C.

2010/1061

Test Programmes

according to

programme

; temperature 60°C;

EN 60456

using a load of 7 kg.

TRRUCH

This appliance conforms to the following

EC Directives:

- 2004/108/EC (Electromagnetic Compa-

tibility)

- 2006/95/EC (Low Voltage)

- 2002/96/EC

3

Connecting the drain hose

! Do not use extension cords or multiple sockets.

Connect the drain hose to

! The cable should not be bent or compressed.

drain duct piping or a wall

drain located between 65

! The power supply cable and plug must only be replaced

and 100 cm above the floor,

by authorised technicians.

making sure it is not bent

at all.

Warning! The company shall not be held responsible in the

event that these regulations are not respected.

Alternatively, rest the

drain hose on the side of

a washbasin or bathtub,

fastening the duct supplied

to the tap (see figure).

The free end of the hose

should not be underwater.

! We advise against the use of hose extensions; if it is

absolutely necessary, the extension must have the same

diameter as the original hose and must not exceed 150 cm

in length.

Electrical connections

Before plugging the appliance into the electricity socket,

make sure that:

• thesocketisearthedandcomplieswithallapplicable

laws;

• thesocketisabletowithstandthemaximumpowerload

of the appliance as indicated in the Technical data table

(see opposite);

• thepowersupplyvoltagefallswithinthevaluesindicated

in the Technical data table (see opposite);

• thesocketiscompatiblewiththeplugoftheappliance.

If this is not the case, have the socket or the plug

replaced.

! The appliace must only be installed indoor in a frost free

and dry room, to prevent it from electronic damage due to

frost or condensation.

! The mains socket must remain within easy reach after the

washing machine has been installed.