Fagor BV-1000X: 4. OPERATING INSTRUCTIONS

10

attempt to repair. If a repair is required, 

contact a Technical Assistance Service 

authorised by the manufacturer and 

request the use of original spare parts.

•

  If the cable for this appliance is 

damaged, contact an authorised 

Technical Assistance Service for it to be 

replaced. 

•

  Do not leave the appliance exposed to 

the elements (rain, sun, ice, etc.).

•

  Do not use or let any part of the 

appliance come into contact or near hot 

surfaces (kitchen gas or electric hobs or 

ovens).

•

  Do not use detergents or abrasive 

sponges to clean the appliance. 

•

  Do not touch the hot surfaces. Use the 

handles.

•

  Do not let the cable come into contact 

with the hot parts of the appliance.

•

  The blade is very sharp. Handle it 

carefully to avoid cuts.

•

  Do not fill the blender any higher than 

the maximum level (1500 ml). 

•

  Do not remove the jug from the motor 

base when the appliance is functioning.

•

  Ensure the jug lid is properly fitted 

before using the blender. 

•

  Do not place your hands or any 

objects in the jug when the blender is 

functioning. If necessary, disconnect the 

appliance and use a spatula to remove 

any food stuck to the walls of the jug. 

•

  Do not submerge the motor base in 

water or any other liquid. 

•

  Do not touch the rotating parts while 

they are in movement. Always wait for 

them to stop.

•

  This appliance must only be used for 

processing food. 

•

  This appliance is not intended for use 

by persons (including children) with 

reduced physical, sensory or mental 

capabilities, or lack of experience and 

knowledge, unless they have been given 

supervision or instruction concerning 

use of the appliance by a person 

responsible for their safety.

•

  Children should be supervised to ensure 

that they do not play with the appliance

•

  When mixing hot liquids/foods excess 

pressure may build up inside the 

4. OPERATING INSTRUCTIONS

Before using the blender for the first time, 

clean the dispenser cap, jug lid, jug and 

blade in warm soapy water and dry them 

thoroughly before assembling them again. 

ASSEMBLY

Unplug the appliance before carrying out 

any dismantling or assembly operations.

1.

  Place the rubber seal 

(4)

 on the edge of 

the blade unit 

(5) (Fig. B).

2.

  Insert the blade unit 

(5)

 in the joint 

(6) 

(Fig. C).

3.

  Screw the bottom part of the glass jug 

(3)

 onto the joint 

(6) 

and turn it anti-

clockwise 

(Fig. D)

. 

4.

  Fit the jug onto the motor base 

(7)

, 

aligning the jug with the grooves on 

the motor base 

(7)

, and then turn it 

clockwise 

(Fig. E)

5.

  Firmly close the lid 

(2) (Fig. F)

. 

6.

  Place the dispensing cap 

(1)

 in the hole 

in the lid and turn it anti-clockwise 

(Fig. 

G)

. 

To dismantle the blender, to clean it for 

example, carry out the assembly process in 

reverse order. 

ADJUSTMENT 

•

  Place the assembled blender on a flat, 

stable surface.

•

  Before plugging in the blender, make 

sure the jug is correctly fitted and in 

place on the motor base

 (7)

. 

 NOTE:

 The blender has a safety lock 

system to ensure the appliance can only 

blender and this could make the lid 

come off and the contents splash out. 

We therefore recommend that you avoid 

mixing excessively hot foods and that 

you only put very small quantities of hot 

liquids or foods into the blender.

•

  Do not use the blender for very hard 

food products, such as bones, shelled 

nuts, frozen meats etc., which could 

either damage the blade or cause the 

motor to seize.

•

CAUTION: 

Do not use the unit 

continuously more than 2 minutes.