Sharp PN-H801: MOUNTING PRECAUTIONS
MOUNTING PRECAUTIONS: Sharp PN-H801
MOUNTING PRECAUTIONS
• This product is for use indoors.
•
A mounting bracket compliant with VESA specications is required.
• Since the monitor is heavy, consult your dealer before
installing, removing or moving the monitor.
•
Mounting the monitor on the wall requires special expertise
and the work must be performed by an authorized SHARP
dealer. You should never attempt to perform any of this work
yourself. Our company will bear no responsibility for accidents
or injuries caused by improper mounting or mishandling.
• Use the monitor with the surface perpendicular to a level
surface. If necessary, the monitor may be tilted up to 20
degrees upward or downward.
•
When moving the monitor, be sure to hold it with the handles,
the unit bottom and sides. Do not grasp the screen and
corners. This may cause product damage, failure, or injury.
•
This monitor should be used at an ambient temperature
between 32°F (0°C) and 104°F (40°C). Provide enough space
around the monitor to prevent heat from accumulating inside.
E
4
For the monitor in landscape orientation
SAFETY INSTRUCTION
- Do not use the monitor where there is a lot of dust, where
- Please be sure to constantly remove dust and garbage that
humidity is high, or where the monitor may come into contact
has attached to the ventilation opening. If dust collects in the
with oil or steam. Do not use in an environment where
ventilation opening or the inside of the monitor, it may lead to
there are corrosive gases (sulfur dioxide, hydrogen sulde,
excessive heat, outbreak of re, or malfunction.
nitrogen dioxide, chlorine, ammonia, ozone, etc.). As this
Please request a cleaning of the inside of the monitor from
could lead to re.
an authorized SHARP servicing dealer or service center.
- Ensure that the monitor does not come into contact with
- The AC outlet shall be installed near the equipment and shall
water or other uids. Ensure that no objects such as paper
be easily accessible.
clips or pins enter the monitor as this could lead to re or
electric shock.
The Power Cord
- Do not place the monitor on top of unstable objects or in
- Use only the power cord supplied with the monitor.
unsafe places. Do not allow the monitor to receive strong
- Do not damage the power cord nor place heavy objects on
shocks or to strongly vibrate. Causing the monitor to fall or
it, stretch it or over bend it. Also, do not add extension cords.
topple over may damage it.
Damage to the cord may result in re or electric shock.
- Do not use the monitor near heating equipment or in places
- Do not use the power cord with a power tap.
where there is likelihood of high temperature, as this may
Adding an extension cord may lead to re as a result of overheating.
lead to generation of excessive heat and outbreak of re.
- Do not remove or insert the power plug with wet hands.
- Do not use the monitor in places where it may be exposed to
Doing so could result in electric shock.
direct sunlight. Risk of cabinet deformation and failure if the
- Unplug the power cord if it is not used for a long time.
monitor is used in direct sunlight.
-
Do not attempt to repair the power cord if it is broken or
malfunctioning. Refer the servicing to the service representative.
• Temperature condition may change when using the monitor
together with the optional equipments recommended by
SHARP. In such cases, please check the temperature
condition specied by the optional equipments.
• Do not block any ventilation openings. If the temperature
inside the monitor rises, this could lead to a malfunction.
• Do not place the monitor on a device which generates heat.
• Adhere to the following when installing the monitor in its
portrait orientation. Failing to adhere to the following may
cause malfunctions.
- Install the monitor such that the power LED is located on
the bottom side.
- Set the MONITOR on the MONITOR menu to PORTRAIT.
(See OPERATION MANUAL.)
• Even when the ambient temperature is
104°F (40°C)
or
less in a portrait installation, the brightness of the backlight
may automatically decrease if the temperature inside the
monitor becomes too hot. This is to prevent further heating
of the interior.
Unit: inch [mm]
• Use the supplied sticker.
7-7/8 [200]
1-7/16 [35]
For the monitor in landscape orientation
2
2
[50]
[50]
2 [50]
For the monitor in portrait orientation
Horizontal sticker
Unit: inch [mm]
(Logo)
7-7/8 [200]
1-7/16 [35]
For the monitor in portrait orientation
2
2
[50]
[50]
Vertical sticker
(Operation panel)
Power LED
2 [50]
•
If it is difcult to provide sufcient space for any reason such
as the installation of the monitor inside a housing, or if the
Be careful not to cover the remote control sensor or
ambient temperature may be outside of the range of 32°F
switches.
(0°C) to 104°F (40°C), install a fan or take other measures to
keep the ambient temperature within the required range.
Оглавление
- Contents
- SAFETY PRECAUTIONS
- SAFETY PRECAUTIONS (Continued)
- MOUNTING PRECAUTIONS
- Supplied Components
- Connections
- Turning Power On/Off
- Specications
- Table des matières
- PRÉCAUTIONS DE SÉCURITÉ
- PRÉCAUTIONS DE SÉCURITÉ (Suite)
- PRÉCAUTIONS POUR LE MONTAGE
- Composants fournis
- Connexions
- Mise sous tension et hors tension
- Caractéristiques
- Índice
- PRECAUCIONES DE SEGURIDAD
- PRECAUCIONES DE SEGURIDAD (Continuación)
- PRECAUCIONES DE MONTAJE
- Componentes suministrados
- Conexiones
- Encendido/apagado
- Especicaciones
- Inhalt
- SICHERHEITSVORKEHRUNGEN
- SICHERHEITSVORKEHRUNGEN (Fortsetzung)
- SICHERHEITSANLEITUNG
- Mitgelieferte Komponenten
- Anschlüsse
- Ein- und ausschalten
- Technische Daten
- Содержание
- ПРАВИЛА ТЕХНИКИ БЕЗОПАСНОСТИ
- ПРАВИЛА ТЕХНИКИ БЕЗОПАСНОСТИ (Продолжение)
- МЕРЫ ПРЕДОСТОРОЖНОСТИ ПРИ КРЕПЛЕНИИ
- Комплектные принадлежности
- Соединения
- Включение/выключение питания
- Спецификации