Fagor 2VFT-320S: 0

e n g l i s h

13

220-240V 3~ 

Nominal switch by phases

60 cm hob 

14 A

>60cm hob 

16,5 A

380-415V 3N~ 

Nominal switch by phases

60 cm hob 

11 A

>60cm hob 

13 A

380-415V 2N~ 

Nominal switch by phases

60 cm hob 

16 A

>60cm hob 

19 A

This appliance is compliant with European 

directives 73/23/EEC and 89/336/EEC

Recommendation: 

The hob must be installed 

by an authorised installer, who shall follow the 

manufacturer’s instructions and diagrams.

1

Instruction Manual

Very important: Read this manual thoroughly before using the hob.

This manual is designed so that the texts relate to the corresponding illustrations.

2

Installation

Use

Identify the model of your hob 

(“

a

”, “

b

”, “

c

”, 

“

d

”, “

e

”, “

f

”, “

g

”, “

h

”, “

i

”, “

j

”, “

k

”, “

l

”, “

m

”, “

n

”, 

“

o

”) by comparing the number and layout of the 

elements on your appliance with that shown in 

the illustrations.

1.1 Unpacking.

 Remove all the protective 

materials.

1.2  Insertion into the unit. 

Always take into 

account the details on the characteristics 

plate (1.2.1) and the measurements of 

the unit into which the hob is going to be 

inserted (1.2.2, 1.2.3). If you are not going 

to fi t an oven beneath the hob, you must 

install a protective panel in accordance with 

the measure indicated (1.2.4). Stick the foam 

join along the outer edge of the hob to make 

it watertight (1.2.5). Turn the hob over and 

insert it into the hole (1.2.6). Secure it to the 

unit with the four hooks supplied (1.2.7). Do 

not use non-removable materials such as 

silicone.

1.3  Connection to the power supply. 

The hob 

is supplied with a power cable. 

• With 5 wires: a) dark blue, b) light blue, c) 

brown, d) red, e) green yellow. (1.3.1)

• Prepared for a 230V~ hob. (1.3.2)

• Prepared for a 220-240V~ hob: see table. 

(1.3.3)

• Total power:  

60cm hob 6.8kW, 

>60cm hob 7.8kW

220-240V~ 

Nominal switch by phases

60 cm hob 

30 A

>60cm hob 

34 A

•  If the type of connection is other than 220-

240V~, remove the cable and make the 

connection as per diagrams (1.3.3, 1.3.4).

0

Identifi cation

Clay, copper or stainless steel receptacles can 

be used with vitroceramic hobs. Aluminium 

receptacles are not recommended as they can 

stain the glass of the hob.

2.1  Selecting the cooking zone. 

You have 

various elements on which to place the 

receptacles. Choose the most suitable one 

depending on the size of the receptacle.

2.2  Turning on the hob.

 Press 

 for 3 

seconds to turn on the hob; the 

0

 of the 

different cooking zones will be activated.

N.B.: In order to be able to select whether 

the child safety function is activated, 

deactivate it by pressing the

 key for 3 

seconds (2.13)

2.3  Activating the element.

 Activate the 

element on which you have placed the 

receptacle by pressing the corresponding 

key  

 (2.3.1, 2.3.2). or 

press    (2.4.2)

N.B.: If you take longer than 5 seconds to 

select the element, the hob will automatically 

turn itself off, as a safety measure.

e n g l i s h

14

fl ash (2.8.7). Select the time with   ,   on 

the clock (2.8.8). After 5 seconds the time 

will be set and the power and     will be 

displayed alternately on the timed element.  

Once the time has passed, you will hear 

a sound and 

00

 will fl ash. To cancel the 

timing, press 

 on the  

 icon until 

00

 is 

displayed.

N.B.: The timer will automatically turn itself off 

if you take longer than 10 seconds to select 

the time.

Models e:

 Once an element has been 

activated and the power selected, press 

again the selection key of the element to 

be timed, and a    will appear.  (2.8.11). 

Select the time with 

 ,  

 (2.8.12) and set 

it by pressing the timed element key again 

(2.8.13). The power will be displayed with a 

dot indicating that the element is on a timer. 

You will hear a sound and see    to indicate 

that the time has passed (2.8.14). Press any 

key and the sound will stop.

N.B.: The timer will automatically turn itself off 

if you take longer than 10 seconds to select 

the time.

Observations on timing: 

If the power level is 9, 

the maximum time for the timer will be 60 min. 

Otherwise, the maximum will be 99 min.

Once the time has passed, the alarm will sound 

until you press any key.

PROGRAMMING FUNCTIONS

2.9 Rapid heating.

 Reaches maximum 

temperature quickly to automatically go to 

the constant temperature.

Models abc:

 Activates an element and takes 

the bar to the maximum power. Press 

and a   will appear on the display screen 

of the selected element (2.9.1). You have 5 

seconds to select the desired level, you are 

advised to use levels from 3 to 6 (2.9.2). After 

fi ve seconds the rapid heating will be set 

and will appear on the display screen of the 

selected element (2.9.1). You have 5 seconds 

to select the desired level, you are advised 

to use levels from 3 to 6 (2.9.2). After fi ve 

seconds the rapid heating will be set and   

and the power will be displayed alternately. 

Once the maximum temperature has been 

reached,    will disappear, leaving the 

power constant. The element will continue 

operating in the conventional way. If you want 

2.4  Selecting the power.

 Adjust it by sliding 

your fi nger along the bar (2.4.1) or by 

pressing    or   (2.4.2, 2.4.3).  

SPECIAL ELEMENTS

2.5  Double element, Triple element.

 Once you 

have selected the power, press 

 , 

and this will activate the double element 

(2.5.1, 2.5.3). If you press  

 (2.5.2) or 

 (2.5.4) again, this will activate the triple 

element. To cancel, press ( 

 , 

 , 

 , 

 ).

2.6 Large hotplate.

 You can use this element 

in a circular way  

 or in a joint way, 

as a large hot plate  

 . Press 

 to 

activate it and press again to deactivate it.

Recommendation: 

on the models with halogen 

elements, the light is so bright that we advise 

you not to look at it when it is on without the 

receptacle.

TIMER FUNCTIONS

2.7  Setting the time 

 .

 When the hob is 

plugged in, the digits on the clock will fl ash 

and will show 

 (2.7.1). Adjust the 

time with the keys    ,    (2.7.2). Follow 

the same procedure whenever the appliance 

is unplugged or the power supply is cut off.

To change the time, press the

 key for 5 

seconds (2.7.3). The time will start to fl ash 

and you will hear a beep; adjust it with the 

keys   ,    .

2.8  Selecting the time.

Models abc:

 Once an element has been 

activated and the power selected, you have 

5 seconds of fl ashing in which to press the 

 key (2.8.1). Select the time required by 

pressing    ,     (2.8.2). After fi ve seconds 

the timer is set and the time will be displayed 

with an illuminated dot beneath the icon of 

the timed element (2.8.3). To alter or see the 

time remaining, press the icon of the timed 

element (2.8.4). To cancel the programming, 

press the     ,    keys simultaneously 

(2.8.5).

Models dfghkmo:

 Once an element has 

been activated and the power selected, 

press the     key on the clock.  

00

   and a  

 will appear on each element (2.8.6). Press  

  on the element to be timed and  

  will