Hama MW1002: d Bedienungsanleitung

d

Bedienungsanleitung

GB

Setting the time (CLOCK)

NOTE

►

The time and programmed settings must be reset

after the batteries are changed.

u

Set the time according to the chapter entitled “Changing

the settings”.

u

Set the minutes by pressing the “+/

” [7] or “-” [16]

buttons, then press the SET button [8].

u

Set the hour by pressing the “+/

” [7] or “-” [16]

buttons.

u

Press the MODE button. The time display flashes

several times in quick succession. The time is shown

in the display [1].

Setting the unit of measurement (UNIT)

You can switch between the units “‰ BAC” (BAC = blood

alcohol content) and “mg/l”.

u

Set the unit of measurement according to the chapter

entitled “Changing the settings”.

u

Press the “+/” [7] or “-” [16] button to select the

appropriate unit of measurement. This unit is then

shown on the display [2 or 10].

u

Press the SET button [8] to save the setting. The

display flashes several times in quick succession and

the device exits the settings mode.

36

MW-1002

00087697bda_neu.indd 3600087697bda_neu.indd 36 03.08.2009 9:58:10 Uhr03.08.2009 9:58:10 Uhr

Cleaning the device (CLEAN)

GB

NOTE

►

To achieve a precise reading, make sure that there

is no leftover alcohol in the measuring chamber

prior to each alcohol test.

u

Start the cleaning process according to the chapter

entitled “Changing the settings”.

u

Press the “+/

” button [7] to start the cleaning process.

ON is shown in the display [1], followed by a countdown

from CL08 to CL00. OFF is displayed when the cleaning

process is finished.

u

Press the SET button [8]. The time is shown in the

display [1].

MW-1002

37

00087697bda_neu.indd 3700087697bda_neu.indd 37 03.08.2009 9:58:12 Uhr03.08.2009 9:58:12 Uhr

d

Bedienungsanleitung

GB

Automatic sensor cleaning (ASC)

NOTE

►

Perform the automatic sensor cleaning:

–

before the device is used for the first time and

–

if the device has not been used for a long

period of time (at least a week).

u

Remove the cleaning cap from the bracket .

u

Apply approx. 3-4 drops of alcohol to the cleaning cap

and insert it into the cleaning opening

.

38

MW-1002

00087697bda_neu.indd 3800087697bda_neu.indd 38 03.08.2009 9:58:14 Uhr03.08.2009 9:58:14 Uhr

GB

CAUTION

The sensor may be damaged if the alcohol

concentration is too high.

Using alcohol with a high concentration may cause

damage to the sensor.

Always use alcohol with a concentration of 3-5%.►

u

Start the sensor cleaning process according to the

chapter entitled “Changing the settings”.

u

If OFF appears in the display, press the “+/ ” button [7].

ON appears in the display.

u

Press the SET [8] button to activate the selected

cleaning process.

The cleaning process should stop automatically after 10

minutes. ASC flashes on the display throughout the entire

cleaning process [1]. The device beeps three times two

minutes before the end of the cleaning process. After the

cleaning process is complete, the device beeps once and

the time is shown in the display.

NOTE

►

The cleaning process can be cancelled at any time

by pressing the MODE button once.

MW-1002

39

00087697bda_neu.indd 3900087697bda_neu.indd 39 03.08.2009 9:58:15 Uhr03.08.2009 9:58:15 Uhr

d

Bedienungsanleitung

u

Loosen the cleaning cap an insert the cleaning cap into

GB

the bracket.

u

Start the device’s self cleaning process (see chapter

“Cleaning the device”).

Performing an alcohol test

NOTE

►

The test cannot provide accurate results unless

you have not smoked or consumed alcohol for at

least 20 minutes prior to testing.

u

Rinse your mouth thoroughly with water. Slide the faceplate

upwards and place one of the plastic tubes (included) onto

the mouth piece [9].

The device beeps once, PH flashes multiple times in the display

[1] and a countdown from PH19 to PH00 is displayed.

After the countdown is complete, the device beeps and BLOW

and READY flash in the display.

u

Blow into the plastic tube for approx. 6 seconds. The device

beeps and the measured value is displayed along with an

alarm message, if necessary (see chapter “Evaluating the

alcohol test”).

40

MW-1002

00087697bda_neu.indd 4000087697bda_neu.indd 40 03.08.2009 9:58:17 Uhr03.08.2009 9:58:17 Uhr

GB

NOTE

►

If the device does not detect a breath sample within

5 seconds after the countdown is complete, it beeps

for an additional 10 seconds. In order to perform

the alcohol test, you must press the SET button [8]

while blowing into the device.

►

If the device still does not detect a breath sample,

ERROR [15] and ERR appear in the display (1) and

the device beeps several times. Restart the alcohol

test by pressing the SET button [8] or by sliding the

faceplate down and back up again.

The device automatically initiates the cleaning process after

each test.

u

Press the SET button [8] if you wish to perform another

test.

u

Remove the plastic tube from the mouth piece and slide

the faceplate downwards in order to end the alcohol

test.

u

Clean the used plastic tube.

MW-1002

41

00087697bda_neu.indd 4100087697bda_neu.indd 41 03.08.2009 9:58:18 Uhr03.08.2009 9:58:18 Uhr