Gorenje wt62113: BEFORE USING THE WASHING MACHINE DESCRIPTION OF THE WASHING MACHINE (picture 1)
BEFORE USING THE WASHING MACHINE DESCRIPTION OF THE WASHING MACHINE (picture 1): Gorenje wt62113
BEFORE USING THE WASHING MACHINE
DESCRIPTION OF THE WASHING MACHINE (picture 1)
1. Remove the packaging and check
• Only use new hoses for connecting the washing
a. Lid
f. Mobility lever (depending on model). To move the
a. Cut and remove the shrink-wrap.
machine to the water supply. Used hoses must not
b. Detergent dispenser
washing machine: pull the handle out a little bit by
be used anymore and should be discarded.
hand and pull it out to the stop with the foot.
b. Remove the top protection and the protective
c. Drum
corners.
g. Adjustable feet
5. Drain hose
d. Pump access behind filter
c. Remove the bottom protection by tilting and
• Firmly connect the drain hose to the siphon or
e. After-Sales Service sticker (behind the filter cover)
turning the washing machine on one rear
another outlet for drain water. (see “Installation”/
bottom corner. Make sure that the plastic part
Connect the water drain hose”).
of the bottom protection (if available on the
INSTALLATION
• If the washing machine is connected to a built-in
model) remains in the packing and not in the
drainage system, ensure the latter is equipped with
Removal of transport bracket
• If you need a longer waterstop hose, contact our
machine bottom.
a vent to avoid simultaneous loading and draining
The washing machine is fitted with a transport bracket
After Sales Service or your dealer.
This is important, as otherwise the plastic part could
of water (siphoning effect).
to avoid any possible damage during transport.
• Check the inlet hose regularly for brittleness and
damage the washing machine during operation.
cracks and replace if necessary.
d. Open the lid by pressing it slightly down while
6. Electrical connection
IMPORTANT: Before using the washing machine,
raising the handle. Remove the polystyrene
the transport bracket at the back MUST be
• The washing machine can be connected without a
• Electrical connections must be carried out by a
removed.
backflow valve.
cushion (depending on model).
qualified technician in compliance with the manu-
e. Remove the blue protective film from the panel
facturer’s instructions and the current standard
1. Unscrew the two screws “A” and the four screws
Water stop anti-flooding system (picture 8)
(depending on model).
safety regulations.
“B” with a flat screwdriver or a No. 8 hex nut box
(if available)
spanner (picture 2).
• After unpacking, make sure that the washing
• The technical data (voltage, power and fuses) are
• Screw the hose to the water supply tap. Turn the
machine is undamaged. If in doubt, do not use the
given on the rating plate on the rear of the washing
2. Remove the transport bracket (picture 3).
tap fully on and check the water-tightness of the
washing machine. Contact After-Sales Service or
machine.
3. Replace the four outer screws “B” on the machine
connection.
your local retailer.
• Do not use extension leads or multi sockets.
and tighten them (picture 2).
• The washing machine must not be connected to
• Keep the packaging materials (plastic bags,
• Access to the mains plug or disconnection from
4. Clip the two covers “C” supplied into the openings
the mixing tap of a non-pressurized water heater!
polystyrene parts, etc.) out of reach of children;
the mains supply via a double-pole switch must be
“D” of the washing machine (picture 4).
• Do not immerse the water stop device of the hose
they are potentially dangerous.
ensured at all times after the installation.
Note: do not forget to replace and tighten the four
into water; otherwise it will loose its protective
• If the appliance was exposed to the cold prior to
• Do not operate the washing machine if it has been
outer screws.
function.
delivery, keep it at room temperature for a few
damaged during transport. Inform the After-Sales
• If the flexible hose is damaged, unplug the washing
hours before operating.
Adjust the feet (picture 5, 6)
Service.
machine from the mains immediately, turn off the
Install the washing machine on a level surface, near
• Mains cable replacement is only to be carried out
tap and replace the hose.
2. Remove the transport bracket
to electrical, water and drain connections.
by After-Sales Service.
• The washing machine is fitted with transport
• If the flexible hose is too short, replace it with a 3
• The washing machine must be connected exclu-
If the floor is uneven, adjust the feet (do not insert
screws and a transport bracket to prevent damage
m Water Stop hose (available from After-Sales
sively by means of a socket with an earth connec-
pieces of wood, cardboard etc. under the feet):
during transport. Before using the washing
Service or from your dealer).
tion, in compliance with the regulations in force. In
1. Screw out the washing machine´s feet by hand
machine you must remove the transport
particular, washing machines installed in premises
with 2-3 clockwise turns and then slacken the
Connect the water drain hose (picture 9)
bracket (see “Installation”/“Removal of transport
containing a shower or a bath must be protected
locknut by wrench.
Unhook the drain hose from the left clip, see arrow
bracket”).
by a differential residual current device of at least
2. Adjust the height of the feet by hand.
“A” on picture.
3. Install the washing machine
30 mA. Earthing the washing machine is obliga-
3. Retighten the locknut by turning it anti-clockwise
Important:
• Place the washing machine on a flat and stable
tory under the law. The manufacturer declines all
towards the washing machine’s bottom.
Do NOT loosen the drain hose from the right con-
floor surface.
liability for injury to persons or animals or damage
nection, see arrow “B” on picture. Otherwise, there
to property deriving either directly or indirectly from
Make sure that the feet are resting correctly on the
• Adjust the feet to ensure that the machine is
is the risk of leakage and of scalding with hot water.
failure to observe the directions in these Instruc-
floor and that the washing machine is perfectly
stable and level (see “Installation”/“Adjust the
Firmly connect the drain hose to the siphon or another
tions for Use.
level and stable (use a spirit level).
feet”).
outlet for drain water.
• When using a residual current circuit breaker
• In case of wooden or so-called “floating floors” (for
The washing machine can be installed in an area 40
If you need to add an extension, use a flexible hose
(RCCB), only use a model marked with
.
instance certain parquet or laminate floors), place
cm wide and 63 cm deep.
of the same size and secure the unions with screw-on
the appliance on a sheet of plywood with a size of
Approximate dimensions:
Note: if you install the machine on thick carpet, adjust
hose clips.
at least 40 x 60 cm and thickness of at least 3 cm,
Width: 400 mm
the feet to ensure that there is sufficient space under
Maximum overall drain hose length: 2.50 m.
which is screwed to the floor.
Height: 900 mm
the machine for the air to circulate.
Maximum drain height: 100 cm.
• Make sure that the ventilation openings in the
Depth: 600 mm
Minimum drain height: 55 cm.
Connect the water inlet hose (picture 7)
base of your washing machine (if available on your
Important:
model) are not obstructed by a carpet or other
1. Carefully screw the water inlet hose to the valve
Make sure there are no kinks in the drain hose and
material.
on the rear side of the washing machine (A); screw
take precautions against it falling while the washing
the other end of the hose to the tap by hand.
machine is running.
4. Water supply
2. Make sure there are no kinks in the hose.
• Connect the water supply inlet hose in accordance
3. Check water-tightness of tap and washing machine
with the regulations of your local water company
connections by turning the tap completely on.
(see “Installation”/“Connect the water inlet hose”).
• If the hose is too short, replace it with a suitable
• Water supply: Cold water only
length of pressure resistant hose (1000 kPa min,
• Tap: 3/4” threaded hose connection
EN 61770 approved type).
• Pressure: 100-1000 kPa (1-10 bar).
GB 3GB 2
Оглавление
- INTENDED USE
- BEFORE USING THE WASHING MACHINE DESCRIPTION OF THE WASHING MACHINE (picture 1)
- ELECTRICAL CONNECTION BEFORE THE FIRST WASH CYCLE
- DETERGENTS AND ADDITIVES CLEANING THE FILTER/ DRAINING RESIDUAL WATER
- TROUBLESHOOTING GUIDE
- ПРЕДПОЛАГАЕМОЕ ПРИМЕНЕНИЕ
- ОПИСАНИЕ СТИРАЛЬНОЙ МАШИНЫ (рис.1)
- ПЕРЕД ПЕРВОЙ СТИРКОЙ
- ЧИСТКА ФИЛЬТРА/ СЛИВ ОСТАВШЕЙСЯ ВОДЫ
- РУКОВОДСТВО ПО ПОИСКУ НЕИСПРАВНОСТЕЙ
- МАҚСАТТЫ ПАЙДАЛАНУ
- КІР ЖУУ МАШИНАСЫН ПАЙДАЛАНУДАН БҰРЫН КІР ЖУУ МАШИНАСЫН СИПАТТАУ (сурет 1)
- БІРІНШІ ЖУУ АЙНАЛЫМЫНАН БҰРЫН ЖУУ ҚҰРАЛДАРЫ МЕН ҚОСПАЛАР
- СҮЗГІНІ ТАЗАЛАУ/ҚАЛҒАН СУДЫ АҒЫЗУ
- ПРИЗНАЧЕННЯ ПРАЛЬНОЇ МАШИНИ
- ПЕРЕД ПОЧАТКОМ ВИКОРИСТАННЯ ПРАЛЬНОЇ ОПИС ПРАЛЬНОЇ МАШИНИ (мал. 1) МАШИНИ
- ПЕРЕД ПЕРШИМ ЦИКЛОМ ПРАННЯ ЗАСОБИ ДЛЯ ПРАННЯ ТА ДОБАВКИ
- ОЧИЩЕННЯ ФІЛЬТРА/ЗЛИВАННЯ ЗАЛИШКІВ ВОДИ
- ПОСІБНИК З УСУНЕННЯ НЕСПРАВНОСТЕЙ