Hotpoint-Ariston ARMXXD 129: инструкция

Instructions for use

WASHER DRYER

Contents

GB

Installation, 2-3

GB

CIS

PL

Unpacking and levelling

Connecting the electricity and water supplies

English,1

ÐÓÑÑÊÈÉ, 13

Polski,25

The first wash cycle

Technical data

Description of the washer dryer, 4-5

BG RO

Control panel

Display

ÁÚËÃÀÐÑÊÈ,37

Românã,49

How to run a wash cycle or a drying cycle, 6

Wash cycles and functions, 7

Table of wash cycles

Wash functions

Detergents and laundry, 8

ARMXXD 129

Detergent dispenser drawer

Preparing the laundry

Special wash cycles

Load balancing system

Precautions and tips, 9

General safety

Disposal

Opening the porthole door manually

Care and maintenance, 10

Cutting off the water or electricity supply

Cleaning the washer dryer

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Troubleshooting, 11

Service, 12

1

Installation

 This instruction manual should be kept in a safe

Levelling the machine correctly will provide it with

GB

place for future reference. If the washer dryer is sold,

stability, help to avoid vibrations and excessive noise

transferred or moved, make sure that the instruction

and prevent it from shifting while it is operating. If it is

manual remains with the machine so that the new

placed on carpet or a rug, adjust the feet in such a

owner is able to familiarise himself/herself with its

way as to allow a sufficient ventilation space

operation and features.

underneath the washer dryer.

 Read these instructions carefully: they contain vital

information relating to the safe installation and

Connecting the electricity and water

operation of the appliance.

supplies

Unpacking and levelling

Connecting the water inlet hose

Unpacking

1. Insert seal A into the

end of the inlet hose and

1. Remove the washer dryer from its packaging.

screw the latter onto a

2. Make sure that the washer dryer has not been

cold water tap with a 3/4

damaged during the transportation process. If it has

gas threaded opening

been damaged, contact the retailer and do not

A

(see figure).

proceed any further with the installation process.

Before performing the

connection, allow the

3. Remove the 4

water to run freely until it

protective screws (used

is perfectly clear.

during transportation) and

the rubber washer with

2. Connect the inlet hose

the corresponding

to the washer dryer by

spacer, located on the

screwing it onto the

rear part of the appliance

corresponding water inlet

(see figure).

of the appliance, which is

situated on the top right-

hand side of the rear part

of the appliance (see

4. Close off the holes using the plastic plugs provided.

figure).

5. Keep all the parts in a safe place: you will need

them again if the washer dryer needs to be moved to

another location.

3. Make sure that the hose is not folded over or bent.

 Packaging materials should not be used as toys for

 The water pressure at the tap must fall within the

children.

values indicated in the Technical details table (see

next page).

Levelling

 If the inlet hose is not long enough, contact a

1. Install the washer dryer on a flat sturdy floor,

specialised shop or an authorised technician.

without resting it up against walls, furniture cabinets

or anything else.

 Never use second-hand hoses.

2. If the floor is not

 Use the ones supplied with the machine.

perfectly level, compen-

sate for any unevenness

by tightening or loosening

the adjustable front feet

(see figure); the angle of

inclination, measured in

relation to the worktop,

must not exceed 2°.

2

Connecting the drain hose

 Do not use extension cords or multiple sockets.

GB

Connect the drain hose,

 The cable should not be bent or compressed.

without bending it, to a

drainage duct or a wall

 The power supply cable must only be replaced by

drain located at a height

authorised technicians.

between 65 and 100 cm

65 - 100 cm

from the floor;

Warning! The company shall not be held responsible

in the event that these regulations are not respected.

The first wash cycle

alternatively, rest it on

Once the appliance has been installed, and before

the side of a washbasin

you use it for the first time, run a wash cycle with

or bathtub, fastening the

detergent and no laundry, using the wash cycle

.

duct supplied to the tap

(see figure). The free end

of the hose should not

be underwater.

 We advise against the use of hose extensions; if it is

Te ch n i c a l d a t a

absolutely necessary, the extension must have the

same diameter as the original hose and must not

exceed 150 cm in length.

Model

ARMXXD 129

width 59.5 cm

Dimensions

height 85 cm

Electrical connections

depth 53,5 cm

from 1 to 7 kg for the wash programme;

Before plugging the appliance into the electricity

Capacity

from 1 to 5 kg for the drying programme

socket, make sure that:

Electrical

please refer to the technical data plate

 the socket is earthed and complies with all

connections

fixed to the machine

applicable laws;

maximum pressure 1 MPa (10 bar)

Wate r

minimum pressure 0.05 MPa (0.5 bar)

connections

 the socket is able to withstand the maximum power

drum capacity 52 litres

load of the appliance as indicated in the Technical

data table (see opposite);

Spin speed

up to 1200 rotations per minute

Wash:

programme

(1

st

press of the

 the power supply voltage falls within the values

button); temperature 60°C;

indicated in the Technical data table (see opposite);

Energy rated

using a load of 7 kg.

programmes

Drying: first drying cycle performed with a

 the socket is compatible with the plug of the

according to

2 kg load, by selecting the "IRON DRY"

washer dryer. If this is not the case, replace the

regulation

dryness level;

socket or the plug.

EN 50229

The second drying cycle is performed

with a 5 kg load, by selecting the

"CUPBORD DRY" dryness level.

 The washer dryer must not be installed outdoors,

even in covered areas. It is extremely dangerous to

This appliance conforms to the following

EC Directives:

leave the appliance exposed to rain, storms and other

- 89/336/EEC dated 03/05/89

weather conditions.

(Electromagnetic Compatibility) and

subsequent modifications

 When the washer dryer has been installed, the

- 2006/95/EC (Low Voltage)

electricity socket must be within easy reach.

- 2002/96/EC

3