Gorenje GI52220AW: HOB BURNER SETTINGS
HOB BURNER SETTINGS: Gorenje GI52220AW
35
HOB BURNER
SETTINGS
MINIMUM OUTPUT
ADJUSTMENT
Before starting any adjustments
disconnect the appliance from the
mains power supply. Adjustments must
be carried out with the tap at the
"SAVING" position.
The minimum gas output is correctly
adjusted when the inner cone of the
flame arrives at the height of 3 to 4
mm.
If this is not the case, first remove the
tap knob and then tighten or loosen the
screw C, depending on whether the
flame is to be reduced or increased.
The adjustments must be crried out so
that the end position of the tap is
actually its minimum position.
For butane/propane the screw C must
be fully screwed in.
-
ғ
,
3 4 .
,
ё
„ ",
,
ғ
-
.
„”ғ
,
’ є
3 4 ғ
,
Ө, ,
’ ғ
/ Ө
ғ
-
ұ
ұ ғ
,
3- 4
- ,
ұ ғ
ұ ,
« »
, ұ
ұ ұ ,
ғ
OVEN BURNER
SETTINGS
PRIMARY AIR ADJUSTMENT
To access the primary air adjusting
screw (5), open or remove oven door
and remove oven bottom (2). By
(Ң),
ұ ғ
36
unscrewing the adjusting screw the
quantity of primary air is increase, by
tightening it is reduced. The air/gas
mixture is correct when the flame has
blue color.
Adjust screw 5 for value X in
accordance with the table, and tighten
the nut.
Check that the burner is working
properly: the flame must be blue and
sharp, without a yellow tip.
(5).
( ,
) (2).
, -
ғ
( „“)
ё ғ
, (қ)ғ
є
, –
єғ /
, ’ є
ғ
Ң Б
, ,
ғ
, є
: ’
ғ
( ,
),
ғ
ұ ұ
ұ, ұ
– ғ
ұ („“ )
ә
ғ
ұ
ұ :
ғ
1 – Front oven wall
2 – Oven bottom
3 – Ignition tube
4 – Oven burner
5 – Oven burner adjusting screw
6 – Grill burner
1 –
2 –
3 –
4 –
5 –
6 –
1 –
2 –
3 –
4 –
5 –
6 – -
1 –
2 –
3 – ұ
4 –
5 – ұ
6 –
37
ADJUSTMENT OF OVEN
BURNER MINIMUM POWER
On completion of this operation,
proceed as follows:
Remove the oven bottom.
Oven control knob
Lift off the oven control knob.
For propane/butane fully tighten screw
G and for natural gas unscrew screw
G Лв К ½ ШЫ ¾ ЭЮЫЧ ПШЫ ЧКЭЮЫКХ РКЬ
Oven temperature selector
Disconnect the cooker from the mains
ЩШаОЫ ЬЮЩЩХвғ LТПř ЭСО ШЯОЧ
temperature selector knob. For
propane/butane fully tighten screw G.
For natural gas unscrew screw G by
К ½ ШЫ ¾ ЭЮЫЧ ПШЫ ЧКЭЮЫКХ РКЬ
Light the oven burner and close the
oven door.
Oven control knob
Set the oven control knob to position
“MAБIMUM POАER” КЧН СОКЭ ЭСО
oven for 15 minutes. Then set the
control knob to the to adjust the flame.
Oven temperature selector
Set the temperature selector control
knob to position 8 and heat the oven for
15 minutes.
Then set the temperature selector knob
to position 1 and use screw G to adjust
the flame.
Right turn reduces the height of the
flame, and left turn increases the
height. The adjustment is correct when
the body of the flame is about 3 to 4
mm high.
Replace the knob and set it to the
switch off position, then replace the
oven base.
If the flame sensor does not operate
properly, check its position according to
fig.
„
“
:
ғ
ғ
, G
,
-, Қ/қ”
3/4”
ғ
“ ”ғ
,
, , ҚҢ ғ
“ ”
G
ғ
, -
ғ
,
3 4 ,
Қң0°Өғ
:
ғ
ғ
ғ
ғ
/
G,
– G ½ ¾
ғ
І
ҚҢ ғ
G
’ ғ
ү
ҚҢ ғ
Қ
G ’ғ
є
’, – є
’ғ
є ,
’ є 3-4 ғ
,
є ғ
’ є
з і
і і й
« »
ә
:
,
ғ
ұ
ғ
- ұ
, G ұ
ұ, ә
ұ Қ/қ” ә
3/4”
ұ,
ғ
ұ “І
” .
ұ,
, ,
, ҚҢ .
ұ
« »
ә G ұ
ғ
ұ ұ
, ұ
– ұғ ,
3- 4
- ,
Қң0°Ө
, ұ
ғ
Оглавление
- OPERATING AND MAINTENANCE INSTRUCTIONS
- CONTROL PANEL
- BEFORE FIRST USE
- OPERATION
- OVEN OPERATION
- GRILL
- ELECTRIC GRILL
- CLEANING AND MAINTENANCE
- WARRANTY TERMS AND CONDITIONS
- DISPOSAL OF OBSOLETE APPLIANCES
- LOCATION
- CONNECTION TO GAS SUPPLY
- HOB BURNER SETTINGS
- GRILL BURNER SETTINGS
- CONVERSION TO ANOTHER TYPE OF GAS
- LEVELING THE APPLIANCE
- EN UA RU KK
- EN UA RU KK
- II
- ACCESSORIES FOR ORDERING
