Beurer WL 70: 8.6 Good night function (radio sleep timer) 8.7 Light functions 8.8 Resetting the device to factory settings 9. Cleaning and storage
8.6 Good night function (radio sleep timer) 8.7 Light functions 8.8 Resetting the device to factory settings 9. Cleaning and storage: Beurer WL 70
Table of contents
- Included in delivery
- 4. Warning notices/safety notes 1. Getting to know your device 2. Signs and symbols 3. Intended use
- 5. Device description 7. Basic settings 7.1 Setting the time 6. Initial use
- 7.2 Setting the alarm properties 7.3 Setting the display brightness 7.4 Setting the snooze duration 7.5 Switching the button tone on/o 8. Device functions 8.1 Setting the alarm
- 8.3 AUX mode 8.4 USB mode 8.2 Switching o the alarm 8.5 Radio mode
- 8.6 Good night function (radio sleep timer) 8.7 Light functions 8.8 Resetting the device to factory settings 9. Cleaning and storage
- 10. Disposal 11. Technical data
2.
Use the / buttons to select the desired programme
function is then activated automatically and a small
number (e.g.
P1
or
P2
) under which a station is to be
icon appears in the display. The light will now go
saved.
out automatically once the configured duration of the
sunset has elapsed.
3.
Press and hold the button to start the automatic
station search. To save a station under the selected
programme number (e.g.
P1), press the
Menu/Set
Note
button.
Sunset with music
The device can also be used to simulate a sunset while
4. To switch between the saved stations, press the
/
you listen to music. In the process, the light slowly
buttons.
turns darker after a set duration. The music is switched
8.6 Good night function (radio sleep timer)
o automatically after the set duration has elapsed.
If radio mode is switched on, you can also enable a good
To start a sunset with music on the device, proceed
night function.
as follows:
You can use the good night function to set the number
1. When the device is switched on, select the desired
of minutes after which the radio should automatically
music source (USB, radio (FM) or AUX).
switch o.
2.
Perform the subsequent steps as in "8.7.2 Sunset
If you wish to use the good night function, proceed as
function".
follows:
1. When the device is switched on, press the FM button
8.7.3 Mood light with change of colour
to access radio mode.
The wake-up light can also be used as a mood light with
change of colour.
2.
Press the Menu/Set button;
2 MIN sleep
appears
in the display.
1.
When the device is switched on, press the Light button
3x.
3. Use the Menu/Set button to set the desired time after
which the radio should automatically switch o (2, 5,
2.
LIGHT change
appears in the display.
10, 15, 20, 30, 45 or 60 minutes). Wait 5 seconds to
3.
If you wish to have a coloured light permanently
confirm the selection. A small icon will subsequently
displayed, this can be set by pressing the Light button
appear in the display.
while the colour-change operation is in progress.
LIGHT
fixed
appears in the display.
8.7 Light functions
4.
To fully switch o the light, press the Light button again.
8.7.1 Reading lamp
8.8 Resetting the device to factory settings
1.
When the device is switched on, press the Light button.
If you wish to reset all settings on the wake-up light to
2.
The light turns on and
20 light
appears in the display.
the factory settings, proceed as follows:
Use the +/- buttons to set the desired brightness for the
1.
Remove the mains adapter of the wake-up light from
light (can be selected between 1-20).
the socket.
3.
To switch the light o again, keep pressing the Light
2.
Press and hold both the Menu/Set button and the Light
button until "
LIGHT off
" appears in the display.
button on the device, which is now switched o, and
8.7.2 Sunset function
reinsert the mains adapter of the wake-up light into
The device can also be used to simulate a sunset. In the
the socket. Keep pressing the buttons about 10 sec..
process, the light slowly turns darker after a set duration.
3. The device has now been reset to the factory settings.
To simulate a sunset with the device, proceed as follows:
9. Cleaning and storage
1.
When the device is switched on, press the Light button
on the side.
•
Clean the device with a dry cloth.
2.
The light turns on and
20 light
appears in the
•
Do not use any abrasive cleaning products.
display; immediately afterwards, use the +/- buttons
•
Ensure that no water enters the device. If this should
on the side to set the desired brightness of the light
happen, reuse the device only when it has fully dried
(can be selected between 1-20). Use the Light button
out.
to confirm.
10 sunset
appears in the display.
•
Never immerse the device or mains part plug in water
3.
Use the +/- buttons on the side to select the desired
or other liquids.
duration of the sunset (2, 5, 10, 15, 20, 30, 45 or
60 minutes), then wait for 5 seconds. The sunset
14
