Zelmer 829: ●

61

3

 Insert the dry 

fi

 ltration module with the SAFBAG 

(25) 

dust bag to the container.

Prepare the vacuum cleaner for operation according 

●

to section B.

4

 The vacuum cleaner starts up with default setting of the 

highest power range. One diode will light on the power level 

indicator 

(6)

. Set the desired power value (this function is 

only available in vacuum cleaners type 829.0) by pressing 

the power adjustment buttons  ,  

(5)

.

ATTENTION! It is strictly prohibited to vacuum without 

the dust bag and the inlet 

fi

 lter or with a damaged 

dust bag. It may cause a failure of the vacuum cleaner 

motor.

SAFBAG dust bag disassembly/assembly

Remove the dry 

fi

 ltration module with the SAFBAG 

●

(25)

dust bag from the container.

ATTENTION! The water 

fi

 lter module/the dry 

fi

 ltration 

module with the SAFBAG dust bag may only be 

removed and inserted when the end of the hose is 

removed from the vacuum cleaner opening.

1

 Pull the SAFBAG dust bag interlock fastening and pull 

the interlock aside.

2

 Pull the fastening which attaches the SAFBAG dust bag 

to the basket to release the dust bag plate.

3

 Remove the dust bag.

4

 Insert the SAFBAG dust bag according to the arrow 

printed on the bag so that the lower part of the bag plate is in 

the slot of the housing. Press the upper part of the bag plate 

to the fastening until you hear a characteristic click and close 

the SAFBAG dust bag interlock.

Insert the dry 

fi

 ltration module with the SAFBAG 

●

(25)

dust bag to the container.

VACUUM CLEANING WITH THE USE OF THE 

WATER FILTER MODULE

1

 Press the “PRESS” button and remove the tank lid.

2

 Insert the partition to the grooves in the container so that 

the shutters are directed downwards. Make sure the partition 

is correctly mounted in the container i.e. the partition 

fi

 ns 

should cover the protrusion in the container.

3

 Fill the container with 1,2 liter of water. The water level 

should be in the range marked on the tank wall.

ATTENTION! Do not operate the appliance with an 

empty container while vacuum cleaning with the use 

of the water 

fi

 lter module.

4

 Insert the 

fi

 ltration unit to the tank, make sure that the two 

air stub pipes are in the openings of the vacuum cleaner body.

Prepare the vacuum cleaner for operation according 

●

to section B.

The vacuum cleaner starts up with default setting of the 

highest power range. One diode will light on the power level 

indicator 

(6)

. Set the desired power value (this function is 

only available in vacuum cleaners type 829.0) by pressing 

the power adjustment buttons  ,  

(5)

.

ATTENTION! Do not operate the appliance for too 

long without replacing the water in the container. 

In case of long-term or very intensive vacuuming 

of large amounts of dirt, the water in the tank which 

constitutes the 

fi

 rst 

fi

 ltration level may in whole or in 

a considerable part be absorbed by the dirt. In such 

a case, exchange the water and continue vacuuming.

Avoid vacuuming surfaces covered with substances which 

may favor an excessive foaming of the water inside the 

tank. If you notice that the water is heavily foamed, add 

a foam neutralizer recommended by the manufacturer of 

the appliance e.g. “G 478 Entschäumer D” in the amount 

indicated on the packaging. It can be purchased in stores 

which offer ZELMER S.A. products or by mail order.

ATTENTION! Vacuuming with the amount of water in 

the tank which exceeds the marked, permissible level 

may cause the water to spill to the outside of the 

appliance. If this situation repeats often, it may lead to 

a fast clogging of the outlet HEPA 

fi

 lter.

ATTENTION! The vacuum cleaner is equipped with 

a 

fl

 oat which will automatically block the suction if the 

foam 

fi

 lter II (9) is heavily dirty or the liquid exceeds the 

maximum level. In such a case switch off the vacuum 

cleaner by pressing the on/off button (1), unplug the 

appliance, clean the 

fi

 lter and empty the container.

PICKING UP WATER

If you want to use the vacuum cleaner to vacuum liquid, the 

vacuum cleaner should be prepared as in the case of vacuum 

cleaning with the use of the water 

fi

 lter module except that:

1

 The container should be empty (without water).

2

 You should use the nozzle for picking up water 

(21)

.

ATTENTION! Do not operate the vacuum cleaner with 

a full container! Do not vacuum large amounts of liquid 

at a time (e.g. with the hose immersed into water).

If the water exceeds the maximum level during vacuuming, 

the 

fl

 oat will automatically block the suction. The maximum 

capacity of the container is about 4,0 l. In such a case proceed 

in the manner described above in the part concerning the 

blocking of suction caused by a dirty foam 

fi

 lter.

End of operation cleaning and maintenance

Switch off the vacuum cleaner by pressing the on/off 

●

button 

(1)

 and unplug the appliance.

Wind the cord by pressing the cord rewind button 

●

(4)

. While 

doing this hold the cord to make sure it is not tangled and 

the plug does not hit the vacuum cleaner housing.

Press the interlock on the hose end and remove the hose 

●

from the opening.

E D

62

Disconnect the telescopic tube from the hose and the 

●

nozzle or brush.

In case of vacuuming or picking up water with the use 

●

of the water 

fi

 lter module, remove the dirty water from 

the tank.

It is recommended to wash the container, 

fi

 lters 

●

(disassembly below) and partition thoroughly after each 

use – changing water several times.

ATTENTION! If you do not clean the above-mentioned 

parts or clean them insuf

fi

 ciently it may lead to the loss 

of the 

fi

 ltration capabilities of the inserts and foam and 

cause the formation of bacteria and mites.

Dry all the cleaned parts thoroughly before reassembly.

Filter disassembly

FOAM FILTER I

1

 Open the lid of the 

fi

 lter unit – press the handle and lift 

the lid.

2

 Take out the 

fi

 lter, wash it under running water, dry and 

reinsert.

Close the 

fi

 lter unit lid by pressing it until you hear 

●

a characteristic click.

FOAM FILTER II

It is recommended to wear rubber protective gloves while 

dismantling the 

fi

 lter.

1

 Grab the foam 

fi

 lter with your 

fi

 ngers and remove it from 

the 

fi

 lter unit body.

2

 Wash under running water, dry and reinsert.

ATTENTION! Do not hand wash the 

fi

 lter foam, do not 

wring it, do not wash it in washing machines. Avoid 

crumpling, stretching and deforming. After cleaning 

dry the foam in room temperature. Never dry the foam 

on heaters, stoves, etc.

INLET FILTER

1

 Press the “PRESS” button and remove the tank lid.

2

 Remove the SAFBAG 

(25)

 dust bag module from the 

container.

3

 Take out the SAFBAG dust bag from the module (see 

chapter TRADITIONAL CLEANING WITH SAFBAG DUST 

BAG – disassembly/assembly of the SAFBAG dust bag).

4

 Release the fastening hook which 

fi

 xes the lid of the 

SAFBAG dust bag module with the basket and pull the 

basket aside.

5

 Take out the 

fi

 lter, wash it under running water, dry and 

reinsert.

6

 Close the basket of the SAFBAG dust bag module by 

pressing it until you hear a characteristic click.

7

 Insert SAFBAG dust bag (see chapter TRADITIONAL 

CLEANING WITH SAFBAG DUST BAG – disassembly/

assembly of the SAFBAG dust bag).

8

 Insert the dry 

fi

 ltration module with the SAFBAG 

(25) 

dust bag into the tank.

Insert and snap the tank lid shut.

●

MOTOR FILTER

A 

fi

 ltration fabric is inserted in the motor cooling cycle which 

is to catch the coal dust which arises due to the natural wear 

and tear of the brushes and the commutator in the motor.

1

 Remove the tank from the vacuum cleaner.

2

 Place the vacuum cleaner with the “wheels upwards” so 

that the upper sloping surface and the handle are rested on 

the 

fl

 oor. Insert a 

fl

 at, narrow tool e.g. a screwdriver into the 

special slot of the 

fi

 lter lid; pry the fastening with an upward 

hand movement (lever principle) which will release the lid 

latch while being bent.

3

 If the motor 

fi

 lter 

(8)

 is dirty, it is possible to rinse the 

fi

 lter 

(8)

 under running water. Remember to dry the above 

mentioned 

fi

 lter before reassembly.

4

 Insert the new/rinsed motor 

fi

 lter 

(8)

, make sure that the 

fi

 lter edges do not remain outside the outline of the section. 

Snap the 

fi

 lter lid shut by 

fi

 rst inserting the lower fastening 

and then pressing the fastening so that the upper fastening 

clicks into place at the edge of the appliance body.

OUTLET HEPA FILTER AND FOAM FILTER III

The HEPA outlet 

fi

 lter should be replaced after about 30 

hours of operation (6 months) or earlier in case of heavy dirt.

1

 Remove the tank from the vacuum cleaner.

2

 Place the vacuum cleaner with the “wheels upwards” so 

that the upper sloping surface and the handle are rested on 

the 

fl

 oor.

3

 Slide the slider of the 

fi

 lter cover interlock to the “open” 

position and remove the 

fi

 lter lid.

4

 Remove the foam 

fi

 lter  III 

(11)

. Rinse or replace if the 

fi

 lter becomes dirty. Remember to dry the 

fi

 lter  before 

reassembly.

5

 Remove the foam 

fi

 lter III 

(11)

 and next remove the HEPA 

fi

 lter by grabbing the handle. Replace with a new one if the 

fi

 lter becomes dirty.

It is recommended to periodically inspect the condition of the 

fi

 lter, especially if there was a water over

fl

 ow to the outside of 

the vacuum cleaner. In case of detecting damage (a break) 

in the 

fi

 lter layer or if the layer is evenly covered with dust, 

the 

fi

 lter should be replace with a new one.

6

 If the HEPA 

fi

 lter is dirty, replace it with a new one or 

rinse under running water. Remember to dry the 

fi

 lter before 

reassembly.

7

 Reinsert the 

fi

 lters, insert the 

fi

 lter lid and press 

fi

 rmly.

8

 Slide the slider of the 

fi

 lter cover interlock to the “closed” 

position.

Turn the vacuum cleaner to its natural position (on four 

wheels).

F G H I J

63

The manufacturer does not accept any liability for any damages 

resulting from unintended use or inappropriate handling. The 

manufacturer reserves his rights for modifying the product any time 

in order to adjust it to law regulations, norms, directives, or due to 

construction, trade aesthetic or other reasons, without notifying it in 

advance.

Ecology – environment protection

Each user can protect the natural environment. It is neither 

dif

fi

 cult nor expensive.

In order to do it: put the cardboard packing into 

recycling paper container; put the polyethylene 

(PE) bags into container for plastic.

When worn out, dispose the appliance to 

particular disposal centre, because of the 

dangerous elements of this appliance, which 

can be hazardous for natural environment.

Do not dispose into the domestic waste disposal!!!