Hotpoint-Ariston CE 6V P6 EU/HA: I n s t alla t ion

GB

1

5

B

efore operating your new appliance please read

this instruction booklet carefully. It contains important

information concerning the safe installation and

operation of the appliance.

 Please keep these operating instructions for future

reference. Make sure that the instructions are kept with

the appliance if it is sold, given away or moved.

 The appliance must be installed by a qualified

professional in accordance with the instructions

provided.

 Any necessary adjustment or maintenance must be

performed after the cooker has been disconnected

from the electricity supply.

P

o

s

itionin

g 

an

d 

le

v

ellin

g

 It is possible to install the appliance alongside

cupboards whose height does not e

x

ceed that of the

hob surface.

 Make sure that the wall in contact with the back of

the appliance is made from a non-flammable, heat-

resistant material (T 90°C).

To install the appliance correctly:

• Place it in the kitchen, the dining room or the bed-

sit (not in the bathroom).

• If the top of the hob is higher than the cupboards,

the appliance must be installed at least 600 mm

away from them.

• If the cooker is

installed underneath a

wall cabinet, there must

be a minimum distance

of 420 mm between this

cabinet and the top of

the hob.

This distance should be

increased to 700 mm if

the wall cabinets are

flammable (

see figure

).

•

D

o not position blinds behind the cooker or less

than 200 mm away from its sides.

• Any hoods must be installed according to the

instructions listed in the relevant operating manual.

L

e

v

elling

If it is necessary to level the

appliance, screw the

adjustable feet into the places

provided on each corner of the

base of the cooker (

see figure

).

The legs* fit into the slots on

the underside of the base of

the cooker.

E

le

c

t

r

i

c

al

 c

onne

c

tion

F

ittin

g 

t

h

e

 p

o

w

e

r

s

upp

l

y c

a

b

le

To open the terminal board:

• Insert a screwdriver into the side tabs of the

terminal board cover.

• Pull the cover to

open it.

To install the cable, follow the instructions below:

• Loosen the cable clamp screw and the wire contact

screws.

 The jumpers are pre-set at the Factory for 230 V

single-phase connection (

see figure

).

• To carry out the electrical connections as shown in

the figures, use the two jumpers inside the bo

x

 (

see

figure

 - labelled “P”).

I n s t alla t ion

HOOD

420

Min.

min. 

650

 mm. with hood

min. 

700

 mm. without hood

mm.

600

Min.

mm.

420

Min.

mm.

*

O

nl

y

a

v

a

il

a

ble

in

ce

r

t

a

in

mo

dels.

N

L2

L1

L3

P

N

L

230V 1N~

H07RN-F 3x4 CEI-UNEL 35364

1

3

2

4

5

16

G

B

N

L3

L1

L2

400V 3N~

H05RR-F 5x2.5 CEI-UNEL 35363

1

3

2

4

5

N

L2 L1

400V 2N~

H05RR-F 4x2.5 CEI-UNEL 35363

1

3

2

4

5

• Secure the power supply cable by fastening the

cable clamp screw then put the cover back on.

C

onnecting

the

suppl

y

ca

b

le

to

the

electricit

y

mains

Install a standardised plug corresponding to the load

indicated on the appliance data plate (

see Technical

data table

).

The appliance must be directly connected to the

mains using an omnipolar switch with a minimum

contact opening of 3 mm installed between the

appliance and the mains.  The switch must be suitable

for the charge indicated and must comply with current

electrical regulations (the earthing wire must not be

interrupted by the switch). The supply cable must be

positioned so that it does not come into contact with

temperatures higher than 50°C at any point.

B

efore connecting the appliance to the power supply,

make sure that:

• The appliance is earthed and the plug is compliant with

the law.

• The socket can withstand the ma

x

imum power of

the appliance, which is indicated by the data plate.

• The voltage is in the range between the values

indicated on the data plate.

• The socket is compatible with the plug of the

appliance. If the socket is incompatible with the

plug, ask an authorised technician to replace it. 

D

o

not use e

x

tension cords or multiple sockets.

 Once the appliance has been installed, the power

supply cable and the electrical socket must be easily

accessible.

 The cable must not be bent or compressed.

The

ca

b

le

must

 b

e

chec

k

e

d

regularl

y

an

d

replace

d

 b

y

authorise

d

technicians

onl

y

.

The

manu

f

acturer

d

eclines

an

y

lia

b

ilit

y

shoul

d

these

sa

f

et

y

measures

not

 b

e

o

b

ser

v

e

d

.

TABLE OF CHARACTERISTICS

Oven dimensions 

(HxWxD)

32x43.5x40 cm 

Volume

56 l 

Useful measurements 

relating to the oven 

compartment

width 42 cm 

depth 44 cm 

height 8.5 cm 

Voltage and frequency

see data plate 

Ceramic hob 

Front Left 

Back Left 

Back Right 

Front Right 

Max. ceramic hob 

consumption 

1700 W 

1200 W 

2200 W 

1200 W 

6300 W 

ENERGY LABEL

Directive 2002/40/EC on the 

label of electric ovens.  

Standard EN 50304 

Energy consumption for Natural 

convection – heating mode:  

Traditional mode 

Declared energy consumption for 

Forced convection Class – 

heating mode:  

Baking. 

This appliance conforms to the 

following European Economic 

Community directives: 

73/23/EEC dated 19/02/73 (Low 

Voltage) and subsequent 

amendments - 89/336/EEC 

dated 03/05/89 (Electromagnetic 

Compatibility) and subsequent 

amendments - 93/68/EEC dated 

22/07/93 and subsequent 

amendments. 2002/96/EC