Vitek VT-1513: MAKING ESPRESSO MAKING CAPPUCCINO

ENGLISH

steam on the right side of the tray grid (10). Be

supply, by setting the knob (6) to the “ ” posi-

careful not to get burns by the outgoing steam.

tion.

- Watch the tray (9) filling, regularly pour out wa-

• Wait till the indicator (5) lights up, then set the

ter and wash the tray (9).

knob (6) to the “

” position, when the cup is

filled with water, switch off water supply by set-

• Switch off the coffee maker, by pressing the

ting the knob (6) to the “

” position, pour out

ON/OFF (14) button, the indicator (15) will go

water from the cup. Depending on the cup size,

out.

repeat this procedure several times, then the

• Let the unit cool down and remove the filter

boiler will be washed.

holder (12) turn the handle to the left. Remove

the remaining ground coffee and wash the filter

Attention!

(13).

- Do not remove the filter holder (12) during the

operation of the coffee maker.

Note:

- To remove the filter holder (12) turn the handle

- The cups should be preliminary heated up, put

to the left and remove the holder.

the cups on the platform (2), during warming

water into the boiler the platform heats up, heat-

MAKING ESPRESSO

ing the cups.

• Make sure that the button (14) is in the “OFF”

position, and the knob (6) – is in the “

” posi-

MAKING CAPPUCCINO

tion.

Attention! Be careful not to get burns by the out-

• Remove the tank (4), fill it with cold water till the

going steam.

MAX mark and place on its place.

• Make coffee, as described in the “MAKING

• Fill the filter (13) with the ground coffee using

ESPRESSO” paragraph, in a cup, which size will

the measuring spoon (16) till the “МАХ” mark;

be enough to add whip foam, milk or cream.

slightly tamp the ground coffee by the back side

• Set the knob (6) to the “

” position, wait till the

of the measuring spoon (16).

indicator (5) lights up.

• Insert the coffee filter (13) into the holder (12),

• Put the cappuccinator pipe tip (7) into a glass

by matching the ledge on the filter (13) with the

filled with cold milk or cream. Set the knob (6)

hole on the holder (12) and turn the filter (13)

to the “

” position. The cappuccinator pipe

clockwise/anticlockwise.

tip (7) should not touch the bottom of the glass,

• Place the filter holder into the coffee maker.

otherwise steam release will be blocked, and

Holder ledges (12) should match the groves on

several seconds are enough to get dense foam.

the boiler, and then turn the filter holder handle

• Close steam supply by setting the knob (6) to

(11) to the right till the clamp.

the “

”position.

• Place the corresponding cup on the tray grid

• Switch off the coffee maker, by pressing the

(10).

ON/OFF (14) button, the indicator (15) will go

• Inset the plug into the socket.

out.

• Switch on the unit by pressing the ON/OFF (14),

button, the indicator (15) will light up.

Important:

• Wait till the indicator (5) lights up, the unit is

- It is necessary that milk for making foam is fresh

ready for making coffee.

and without additives, is not long storage milk.

• Switch on water supply, by setting the knob (6)

Take usual whole milk with fat status from 4 to

to the “

” position, watch the process of the

6%, cream fat status should be not less than

cup filling with coffee.

10%.

• To switch off water supply, set the knob (6) to

- Immediately after whisking milk or cream clean

the “

” position.

the cappuccinator pipe and the tip (7) – im-

merse the cappuccinator pipe with the tip (7)

Note:

into a glass with water, switch on steam supply,

- After setting the operating modes knob (6) to

by setting the knob (6) to the “

” position, af-

the “

” position, pressure will be released, the

ter it close steam supply and switch off the cof-

remaining hot water is supplied in the tray (9),

fee maker.

you will hear a sound signal and see outgoing

- Wait till the coffee maker cools down and remove

4

4

1513.indd 41513.indd 4 10.06.2010 15:21:4810.06.2010 15:21:48