AEG KRC 4350 BT: English

36

English

15 Speakers

CAUTION:

16 Battery compartment

• Useascrewdriverandnotacordlessscrewdriver.

17 LCD display

• Ifyouusedifferentscrewsorifthethicknessofthe

cabinetooristoosmall,thescrewsmaypushthrough

Rear side (not shown)

thecabinetoor.

Power cord

• Nowhangtheradioontothemountingplateandpushit

Wire antenna

backwards until it clicks into place.

Sub-structure assembly instructions

Start-up of the device / Introduction

If you don’t want to use the device as a standalone appliance,

• Readtheoperatinginstructionsthoroughlybeforethe

then please assemble it as follows:

start-up!

• Removeallobjectsfromthecupboardandanything

• Ifapplicable,removetheprotectivelmfromthedisplay.

which is fragile in the adjacent cupboards.

• Fortheinstallationthecupboardmustfullthefollowing

Location

conditions:

• Foldoutthestands(14).

Thicknessofthecupboardoor

• Selectasuitablelocationforthedevice.Suitablewould

between 16 mm and 20 mm.

be an even, non-slip surface on which you can easily

• Thewallmountingofthecupboardmustbestableand

operate the device.

anchored firmly in the wall with at least 2 screws.

• Ensurethatthedeviceisadequatelyventilated.

• Important! Do not install the device above a cooker!

• Wheninstallingthedeviceitmustbeensuredthatthere

Inserting the power reserve batteries

is a power socket within reach.

(Batteries not included)

• Themainssocketmustbewithineasyreach,sothatthe

In case of a power failure or if the power plug of the device

plug can be quickly removed in an emergency.

is disconnected from the outlet, then the settings will be

• Important! Do not connect the device to the mains

retained if the power reserve batteries have been inserted.

power supply until after installation!

1. Open the battery compartment on the bottom.

• Thedevicecannotbeinstalledundercupboardsunder

2. Insert 2 AA/R6 1.5 V type batteries. Pay attention to the

which there is a lighting strip.

correct polarity (see bottom of battery compartment)!

• Formounting,youmayneedthefollowingsupplies:

3. Close the battery compartment again.

Reamer or nail, screwdriver, measuring tape, adhesive

4. If the device is not used for a long period of time, then

tape, scissors, safety goggles.

remove the batteries from the device to prevent the bat-

tery acid from leaking.

Supplied mounting accessories

WARNING:

4 Screws (if necessary, check the battery compartment)

1 Drilling template

Thebatteriesshallnotbeexposedtoexcessiveheatsuch

as sunshine, fire or the like. Danger of explosion!

CAUTION:

• Pleaseadheretothedimensionsstatedintheinstalla-

CAUTION:

tion instructions.

• Differentbatterytypesornewandusedbatteriesmay

• Youshoulduseonlytheinstallationaccessoriessup-

not be used together.

plied.

• Batteriesdonotbelonginthehouseholdwaste.

Dispose of spent batteries at the designated collection

points or at the dealer.

Installation

• Stickthetemplatetothebottomofthewallcabinetwith

adhesive tape. With the help of a gimlet or nail pierce the

Power supply

crosses at the attachment points and use it to mark the

• Inserttheplugintoaproperlyinstalled230V,50Hzpower

holes.

socket. 1- 1 0:00 will appear on the display. Please ensure

• Removethemountingplate(2)fromthedevice.Todoso,

that the mains voltage corresponds to the information on

firmly press the mounting plate backwards.

the type plate.

• Removethetemplateandtthemountingplatewiththe

• Ifyouhavenotinsertedanyreservebatteries,thepreset

4 screws below the cabinet.

time will get lost as soon as the power supply has been

interrupted.