AEG US 900 XE: instruction
Class: Power tools
Type: Hacksaw
Manual for AEG US 900 XE
US 900 XE
English
8
Deutsch
10
Français
12
Italiano
14
Español
16
Português
18
Nederlands
20
Dansk
22
Norsk
24
Svenska
26
Suomi
28
Ελληνικά
30
Türkçe
32
Česky
34
Slovensky
36
Polski
36
Magyar
40
Slovensko
42
Hrvatski
44
Latviski
46
Lietuviškai
48
Eesti
50
Òåõíè÷åñêèå äàííûå, Ðåêîìåíäàöèè ïî òåõíèêå áåçîïàñíîñòè,
Pусский
Èñïîëüçî- âàíèå, Ïîäêëþ÷åíèå ê ýëåêòðîñåòè, Îáñëóæèâàíèå, Ñèìâîëû
52
Òåõíè÷åñêè äàííè, Ñïåöèàëíè óêàçàíèÿ çà áåçîïàñíîñò, Èçïîëçâàíå ïî ïðåäíàçíà÷åíèå,
Български
ÑÅ-Äåêëàðàöèÿ çà ñúîòâåòñòâèå, Ñâúðçâàíå êúì ìðåæàòà, Ïîääðúæêà, Ñèìâîëè
54
Română
56
Òåõíè÷êè Ïîäàòîöè, Óïàòñòâî Çà Óïîòðåáà, Ñïåöèôèöèðàíè Óñëîâè Íà
Мaкeдohcки
Óïîòðåáà, Åó-äåêëàðàöè¼à Çà Ñîîáðàçíîñò, БАТЕРИИ, Îäðæóâàњå, Ñèìáîëè
58
技术数据, 特殊安全指示, 正确地使用机器, 电源插头, 蓄电池, 维修, 符号 请详细阅读并妥善保存！
中文
60
IIII II
IV
V
VI
TIP
Písluenství
Äîïîëíèòåëü
配件
2.1.
I
max.
1.
2.
3.
Max
2
II
3
Start
III
Stop
4
1.
2.
IV
3. 4.
5
TIP
1.
1
2
V
2.
3.
6
TIP
1.
V
2.
3.
7
TECHNICAL DATA
US 900 XE
Reciprocating Saw
Production code 4196 21 01...
4196 11 01...
... 000001-999999
Rated input 900 W
-1
Stroke rate under no-load 0-3500 min
Lengths of stroke 19 mm
Weight according EPTA-Procedure 01/2003 2,9 kg
Noise/Vibration Information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K=3dB(A))
89,5 dB(A)
Sound power level (K=3dB(A))
100,5 dB(A)
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined according to EN 60745.
Cutting boards
2
Vibration emission value a
18,3 m/s
GB
h, B
2
Uncertainty K=
1,5 m/s
Cutting wooden beams
2
Vibration emission value a
20,0 m/s
h, WB
2
Uncertainty K=
1,5 m/s
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and
may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for dierent applications, with
dierent accessories or poorly maintained, the vibration emission may dier. This may signicantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched o or when it is running
but not actually doing the job. This may signicantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eects of vibration such as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
WARNING! Read all safety warnings and all instruc-
Before doing any work on the machine, pull the plug out of the
tions, including those given in the accompanying brochure.
socket.
Failure to follow the warnings and instructions may result in electric
Only plug-in when machine is switched o.
shock, re and/or serious injury.
Keep mains lead clear from working range of the machine. Always
Save all warnings and instructions for future reference.
lead the cable away behind you.
Always use the protective shields on the machine.
SAFETY INSTRUCTIONS
Do not use cracked or distorted saw blades.
Wear ear protectors. Exposure to noise can cause hearing loss.
Plunge cuts without pre-drilling a hole are possible with soft
materials (wood, light building materials for walls). Harder materials
Hold power tool by insulated gripping surfaces, when perfor-
(metals) must rst be drilled with a hole corresponding to the size of
ming an operation where the cutting accessory may contact
the saw blade.
hidden wiring or its own cord. Cutting accessory contacting a
„live“ wire may make exposed metal parts of the power tool „live“
When working in walls ceiling, or oor, take care to avoid electric
and could give the operator an electric shock.
cables and gas or waterpipes.
Appliances used at many dierent locations including open air should
be connected via a residual current device (FI, RCD, PRCD) of 30mA
SPECIFIED CONDITIONS OF USE
or less.
This sabre cut is intended to cut wood, plastic, and metal. It can cut
Always wear goggles when using the machine. It is recommended to
straight lines, curves, and internal cut-outs. It cuts pipes and can cut
wear gloves, sturdy non slipping shoes and apron.
ush to a surface.
The dust produced when using this tool may be harmful to health. Do
Do not use this product in any other way as stated for normal use.
not inhale the dust. Wear a suitable dust protection mask.
Sawdust and splinters must not be removed while the machine is
running.
English
8
MAINS CONNECTION
SYMBOLS
Connect only to single-phase AC current and only to the
Please read the instructions carefully before starting the
system voltage indicated on the rating plate. It is also possible
machine.
to connect to sockets without an earthing contact as the design
conforms to safety class II.
CAUTION! WARNING! DANGER!
ECDECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described
Always disconnect the plug from the socket before
under “Technical Data” fullls all the relevant regulations and the
carrying out any work on the machine.
directives 2011/65/EU (RoHs), 2004/108/ EC, 2006/42/EC and the
following harmonized standards have been used:
Accessory - Not included in standard equipment, availa-
EN 60745-1:2009 + A11:2010
ble as an accessory.
EN 60745-2-11:2010
EN 55014-1:2006 + A1:2009 + A2:2011
Do not dispose of electric tools together with household
EN 55014-2:1997 + A1:2001 + A2:2008
waste material! In observance of European Directive
EN 61000-3-2:2006 + A1:2009 + A2:2009
2002/96/EC on waste electrical and electronic equipment
EN 61000-3-3:2008
and its implementation in accordance with national law,
electric tools that have reached the end of their life must
be collected separately and returned to an environmen-
Winnenden, 2013-07-01
tally compatible recycling facility.
GB
Class II construction, tool in which protection against
electric shock does not rely on basic insulation only, but
in which additional safety precautions, such as double
insulation or reinforced insulation, are provided.
Alexander Krug / Managing Director
Authorized to compile the technical le
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
Use only AEG accessories and spare parts. Should components need to
be replaced which have not been described, please contact one of our
AEG service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state
the machine type printed as well as the six-digit No. on the label
and order the drawing at your local service agents or directly at:
Techtronic Industries GmbH, Max-Eyth-Straße10, 71364Winnenden,
Germany.
English
9
