Brother PR650e: инструкция

—————————————————————————————————————————————————————————————————————————————————

Table Set Installation Manual

When using the border, quilt, flat or jumbo frame, it is recommended that the table be used for additional

support.

1/4

Preparing for installation

● When carrying the table, be sure to hold it

Remove the two screws on each machine

with both hands.

1

arm using the Phillips screwdriver included

● Attach the table to the machine before

with your machine or one of your own.

installing the embroidery frame.

● Do not place heavy objects on top of the

installed table or press down on it.

● Remove the table from the machine while

using embroidery frame that do no need to

be used with the table or while

embroidering tubular items, bags or caps.

The embroidery frames for these types of

objects cannot be installed while the table

is attached to the machine.

Verifying the package

contents

Check that the following parts are included. If any

1 Screws on machine arm

item is missing or damaged, contact your

Place a washer onto each of the four

authorized sales representative.

2

hexagonal support screws.

■ Included parts

1. 2. 3. 4.

Insert the hexagonal support screws with

3

washers (two on each side).

5. 6. 7. 8.

Hand-tighten each hexagonal support screw.

No. Part Name

1

Table

2

Left table bracket

3

Right table bracket

4

Hexagonal support screws (4)

5

Washers (4)

6

Screws (4)

7

Wrench

8

Installation manual

2/4

———————————————————————————————————————————————————————————————————————————————————

Using the included wrench, firmly tighten

Attach the left table bracket following steps

4

7

each hexagonal support screw (two on each

5 and 6 for the left side.

side).

Using the Phillips screwdriver included with

8

your machine or one of your own, firmly

tighten all screws.

Align the holes in the right table bracket

5

with the hexagonal support screws on the

right side of the machine.

X The right and left table brackets are

installed on the machine.

1 Hexagonal support screws

2 Holes in right table bracket

Align the right table bracket with the holes

6

in the two hexagonal supports, insert the

screws and lightly tighten to hold the

bracket in place.

1 Screws

● Even if you sew without using the table,

you can leave the brackets attached.

—————————————————————————————————————————————————————————————————————————————————

Slide in the table while supporting it so that

4

Installing the table

it remains level. Push the table in until it

lightly touches the machine.

Loosen the two thumb screws 5 to 6 turns.

• If the table does not move smoothly,

1

slightly lift it up, and then slide it in.

Position the table so that the notch at the

2

center aligns with the machine bed, and then

place the table flat on the guide plates.

While looking below the table, lightly lift it

5

up, and then lower it so that the screw fits

into the notch at the front of the guide plate.

1 Notch in table

2 Machine bed

3 Guide plate

Pull the table toward you slowly, until the

3

pins on the mounting brackets (attached on

each side to the bottom of the table) fit into

the notches in the guide plates.

1 Notch at front

Tighten the two thumb screws so that the

6

table is secured.

1 Thumb screw

1 Pin

2 Notch

3/4

4/4

———————————————————————————————————————————————————————————————————————————————————

After the pins on each side reach the notches

3

Removing the table

in the guide plates, raise the table to lift the

pins up through the notches.

Loosen the two thumb screws, lift up the

1

table, and then pull it off toward you.

1 Thumb screw

1 Pin

2 Notch

X Remove the table from the machine.

Slightly tighten the thumb screws on the

4

table to prevent loss.

Carefully pull out the table so that it does

2

not hit the machine.