Vitek VT-4029 SR: OPERATING THE DEVICE MUTE FEATURE EQUALIZER PRESETS OPERATIONAL SAFETY SOUND EFFECTS: VOLUME LEVEL

ENGLISH

OPERATING THE DEVICE

4. To delay the sound from 0–15 ms, press the SURROUND DELAY but-

Choose the signal source and sound format.

ton (delays rear channels) (9) and CENTER DELAY (delays the center

channel) (10).

1. Digital source

In order to use a digital input signal, press the INPUT (9) (2) button and

MUTE FEATURE

choose the OP or (Optical) or CO (Coaxial) input.

Press the MUTE button (12) to turn off the sound temporarily; the

During MP3 or CD playback on a DVD player, the sound will be repro-

STANDBY (12) indicator will begin to blink. Press the MUTE (12) button

duced in the two-channel PCM format.

again to restore the sound.

2. AUX1 / AUX2 source

EQUALIZER PRESETS

To reproduce sound from a CD or DVD player (when connected using an

In order to select an appropriate sound tone, press the PRESET EQUALIZER

RCA cable), press the INPUT button and choose the AU (AUX2) or CD

button on the front panel of the device consecutively. The presets can be

(AUX1) source.

selected in the following order: Flat, Classic, Pop, and Rock.

Note:

OPERATIONAL SAFETY

This system has built-in Dolby Digital (AC3)/Dolby Prologic.

The main unit, speakers and remote control unit must not be exposed to

moisture, and it is also not recommended to place vases or other contains

SOUND EFFECTS:

full of water on these components.

In order to choose one of these sound effects (Dolby Pro Logic, 3 STEREO

The device is only completely disconnected from the electrical network

or STEREO), press the SURROUND MODE (7) (4) button.

when the power plug is removed from the electrical outlet.

Do not obstruct access to the power plug, which should be accessible at

In Dolby Pro Logic mode you can choose the center speaker’s sound

all times while the device is in operation.

mode.

Moisture

Normal:

Do not expose the device to rain, moisture or dust. Any liquid, if poured

(all six speakers and their indicator are active).

onto the main unit, its buttons or the remote control unit, may cause elec-

This mode should be used when a compact speaker, which cannot pro-

trical burns or cause the device to malfunction. If you accidentally spill

duce bass sounds lower than 100 Hertz, is used as the center speaker.

liquid on the device, immediately disconnect the power cord from the

Low-frequency signals will be distributed to the front left and right speak-

electrical outlet, and then contact and authorized service center.

ers.

Housing components

Wide:

Do not remove and component attached to the housing of the device, as

(all six speakers and their indicator are active).

this may lead to electric shock.

This mode should be used if the center speaker is the same size as the

front left and right speakers and can reproduce sound frequencies lower

Standby mode

then 100 Hertz.

The STANDBY ON/OFF button (10) (1) on the remote control unit discon-

nects the amplifier completely from power, and then continues to use

Phantom:

electricity. In the interests of safety and to avoid excessive electricity

(five speaker indicators are active, the center speaker is turned off).

costs, do not leave the device in standby mode if you will be gone for a

This mode should be chosen if the center speaker is no being used.

long period of time. Disconnect the power cord from the electrical outlet.

The center channel will be split between the front left and right speakers.

If the 3 Stereo mode is chosen, the front left and front right speakers, the

Open flame

subwoofer, and the corresponding indicators should be active.

Do not place open flames, like candles, on or near the device.

In Stereo mode, the front left and front right speakers are active, as well

as the subwoofer and the corresponding indicators.

Power cord

The Dolby Pro Logic mode excludes the use of the NORMAL, WIDE, and

Make sure that the device is not sitting on the cord, because it can get

PHANTOM center channel modes.

damaged and become a threat to the safety of others.

Each of these modes stipulates a set of parameters to be used for the

center channel (echo).

Packaging

Each of these modes has its own signal delay (or echo).

Save the factory packing materials is possible in case you need to trans-

- NORMAL provides true Dolby Pro Logic sound.

port the device. Try to transport the system only in its factory packaging.

- WIDE allows you to achieve different acoustical divisions of the center

channel.

Wiring

- PHANTOM turns off the center channel.

Make sure that all electrical connections (including the power plug, ex-

- The front right and left channels can imitate the sound of the center

tension cord and other electrical connections of separate devices) are

channel.

made carefully and in accordance with the manufacturers requirements.

- The center speaker is not used.

Pressing the EFFECT button on the remote control unit allows you to

Ventilation

choose from the following sound effects: Movie, Classical, Panorama or

Do not allow the ventilation openings to become blocked. Overheating

2.1.

can cause damage to the device and negatively affect the system’s op-

erating abilities.

VOLUME LEVEL

1. In order to change the volume level, use the volume regulator knob (2)

Care and Cleaning

located on the front panel of the device or the VOLUME UP/DOWN (2)

The device should be disconnected from power before cleaning. Use a

buttons located on the remote control unit. The volume level will be

lightly damp napkin and never use aerosols or abrasive cleaners.

shown on the display screen (0–22).

2. The volume of each of the six speakers can be set independently by

Safety

pressing the SPEAKER SETUP button (3). After the indicator for the

Under no circumstances should you allow anybody, especially children,

corresponding speaker begins to blink, set the desired volume level

to insert anything into the jacks, grooves or other openings in the device’s

using the volume regulator knob (1) within the bandwidth of +/-6 dB.

housing as this can lead to electric shock and device malfunction.

3. In order to verify that all five speakers and the subwoofer are correctly

Never continue to use the device if you are even the slightest bit in doubt

connected, press the TEST TONE (8) (5) button. A test signal will be

regarding its operability, or if it is damaged – turn it off, remove the power

sent to each speaker in the following order: front left, center, front

plug from the electrical outlet and contact a service center.

right, rear left, rear right, subwoofer.

While the corresponding indicator is blinking, you can set the volume

level of the test signal. Press the TEST TONE button (8) (5) repeatedly

to stop the test signal.

5

4029.indd 54029.indd 5 07.04.2006 15:53:2907.04.2006 15:53:29