Vitek VT-3606: OPERATING CONTROLS (FIG. A) MAINTENANCE INSTALLATION SAFETY MEASURES INSTALLING THE UNIT IN YOUR AUTOMOBILE ISO JACKS (FIG. C)

ENGLISH

CAR AUDIO CD/MP3 PLAYER WITH DIGITAL

Plug A

RADIO RECEIVER

1.

2.

Model VT - 3606

3.

4. Yellow wire: Memory +12 V

OPERATING CONTROLS (FIG. A)

5. Blue wire: Antenna power

1. Power ON/OFF ( )

6.

2. Settings menu button (SEL): Bass / Treble /

7. Red wire: +12 V (to ignition)

Channel Balance / Fader / Traffic Information

8. Black wire: Ground (-)

Reception / Alternative Frequencies / Changing

Note: Contact 7 of plug A should be connected

Stations / Audio Processor / Tone

to the cars ignition so that the deck is turned off

Compensation / Shock protection mode /

when the engine is not running and doesnt

Audible signal / Scan / Radio operating mode /

wear down the battery.

Radio Settings / default volume level setting.

3. Increase / Decrease volume knob (VOL

Plug B

UP/DOWN)

1. Violet wire: Right rear speaker (+)

4. Radio station preset buttons (1,2,3,4,5,6)

2. Violet wire with black stripe: Right rear speaker

5. AF/REG function  to scan for radio stations

(-)

on different frequencies

3. Gray wire: Front right speaker (+)

6. TA function  to search for traffic information

4. Gray wire with black stripe: Front right speaker

7. PTY function  to choose preferred program

(-)

types

5. White: Front left speaker (+)

8. Display mode setting (DISP)

6. White wire with black stripe: front left speaker (-)

9. MODE select button

7. Green wire: Left rear speaker (+)

10.BAND select button

8. Green wire with black stripe: Left rear speaker(-)

11.Automatic or manual radio station tuning (fre-

quency up (UP) : or frequency down (DOWN)

MAINTENANCE

9) / CD Track/Search

Changing the fuse

12.Automatic radio station search (AS/PS)

If the fuse burns out, check the connection to

13.Automatic band scanning (SCN)

power and replace the fuse. If the fuse burns out

14.Sound muting button (MUTE)

again after being replaced then there may be

15.LCD screen

and internal malfunction. If this happens, con-

16.Button for remove front panel ( )

sult with your nearest service center.

17.Disc slot

Warning

18.Disc eject button (EJ)

Use a fuse of the indicated current level for each

19.Button for pausing playback (PAU)

20.Introduction mode playback button (INT)

wire. Using fuses with high current levels can

(Preliminary playback of all tracks)

lead to serious damage.

21.Track repeat button (RPT)

22.Random playback button (RDM)

INSTALLATION

23,24. Quick jump + 10 tracks up/down. (For MP3

files)

SAFETY MEASURES

 Carefully choose the installation location so that

INSTALLING THE UNIT IN YOUR AUTOMOBILE

the device will not impede the normal operation

(FIG. B)

of the automobile.

1. The device

 Avoid installing the device in places where it may

2. Guide rails

be subjected to sources of high temperatures,

3. Front panel

such as direct sunlight, hot air from the heater,

4. Hex bolt

or where it can me damaged by dust, dirt or

5. Lock-nut

excessive shock.

6. Flat disc

 For safe and reliable installation use only the

7. Car body

parts provided.

8. Bracket

 Remove the front panel before installing the

9. Securing screws

device.

10.M5 hex bolts X 15

Setting the installation angle

ISO JACKS (FIG. C)

The allowable degree of slant from the horizon-

Line audio out (RCA):

tal position is no more than 20°.

Gray: Red (right channel)

: White (left channel)

4