Binatone MGR-3030: BEFORE USE

15.Adapter for fixing the graters

16.Pusher for using the graters

17.Coarse grater

18.Fine grater

19.Shredder

20.Power cord storage compartment

BEFORE USE

 Remove all packing materials from the ap-

pliance.

 Wipe the housing with a damp lint free

cloth and wash all parts to be in contact with

food.

 Rinse the washed parts of the appliance

with clean water and completely dry them be-

fore assembling.

DIRECTIONS FOR USE

Assembling

1. Insert the screw (8) into the operating unit

(5).

2. Put the cross-shaped cutter (9) on the end of

the screw (8) so that the rounded tip of the

cutter (9) is facing the screw (8). Make sure the

cross-shaped cutter (9) is properly fixed.

3. Place the selected perforated disc (10) on top of the cutter (9)

so that the projections on the disk fit the slots in the operating

unit (5).

4. Tighten the seal ring (11).

5. To attach the operating unit (5) to the housing (1) insert it into

the opening in the grinder’s housing, match the arrow on the

operating unit (5) with the symbol on the housing, push

gently and turn anticlockwise to match the arrow on the oper-

ating unit (5) with the symbol on the housing (Picture B)

6. Place the tray (7) on top of the funnel of the operating unit

(5). Now the grinder is ready for operation.

Dismantling

1. Push gently on the operating unit (5), turn it clockwise to

match the arrow on the operating unit (5) with the symbol

on the housing. Remove the operating unit (5) from the motor.

2. Untwist the seal ring (11).

3. Remove the perforated disk (10) and cross-shaped cutter (9)

from the screw(8). Remove the screw (8) from the operating

unit (5).

Use of the applinace

1. Place the grinder on a dry, smooth flat horizontal surface.

2. Remove the meat from the package. Cut out all bones and

6

tendons from the meat prior to grinding. Cut the meat into

pieces that will fit easily into the grinder funnel.

3. Assemble the meat grinder and plug it into a power supply

with voltage matching the information on the appliance.

4. Put the meat into the tray (6).

5. Switch on the appliance using the On/Off/REV button (2).

6. Gradually push the meat pieces into the funnel using the

pusher (7). Do not push too hard.

ENGLISH

7. After use switch the appliance off and unplug it from the wall

outlet.

Note: the grinder will mince up to 1 kg of meat per minute.

If the operation slows down or the motor stops, it

means that probably some pieces of meat are stuck in

the grinder. Immediately switch the appliance off. Set

the switch button in “REV” position. This will

facilitate movement of meat in the opposite direction.

Release the button and switch the grinder on again. If

the meat is still stuck in the grinder, switch it off and

unplug it from the wall outlet. Disassemble and wash

the appliance according to instructions.

Use of the graters

The coarse grater (17) and fine grater (18) are intended for

grating products into thick and thin pieces. These graters are ideal

for carrot, beet, horse radish, cheese etc.

The shredder (19) is intended for coarse shredding. It is ideal

for cabbage, cucumbers, onion etc.

1. To attach the operating unit for the graters (17,18,19) to the

housing (1) insert it into the opening in the grinder’s housing,

match the arrow on the operating unit (5) with the symbol .

on the housing, push gently and turn anticlockwise to match

the arrow on the operating unit (5) with the symbol on the

housing.

2. Put the selected grater (17,18,19) into the operation unit to

fit the slots on the attachment with the projections on the

adapter (15). The grater (17,18,19) should completely go

into the operating unit (5).

3. Push on the product with the pusher (16).

Use of the kebbe attachment

1. Insert the screw (8) into the operating unit (1).

2. Put the kebbe attachment (13) onto the end of the screw (8).

Make sure the projections on the attachment match the slots

on the operating unit (5). Tighten the seal ring (11).

3. Fasten the assembled operating unit (5) onto the housing (1).

4. Place the tray (6) on top of the funnel of the operating unit

(5). The appliance is then ready for operating. A Kebbe recipe

is provided in the “Useful tips”.

7