Vitek VT-8517 ST: BEFORE USING THE UNIT USING THE BLENDER

4

• Do not use the unit if the motor unit body,

– The blender is not intended for beating eggs,

the power cord or the plug is damaged, if

making potato mash, kneading dough or

the unit works improperly or after it was

extracting fruit or vegetable juice.

dropped.

– The amount of products to be processed

• Do not attempt to repair the unit. Do not disas-

should not exceed 2/3 of the capacity of

semble the unit by yourself, if any malfunction

the bowl in which they are processed or be

is detected or after it was dropped, unplug

below the minimal mark of the blender bowl

the unit and apply to any authorized service

“500 ml”.

center from the contact address list given in

• Close the blender bowl (3) with the lid (2).

the warranty certificate and on the website

• Make sure once again that the blender bowl

www.vitek.ru.

(3) is installed correctly and fixed.

• Keep the unit out of reach of children.

• Insert the measuring cup (1) into the lid (2)

opening, matching the corresponding marks

THE UNIT IS INTENDED FOR HOUSEHOLD

on the measuring cup (1) and the lid (2), and

USAGE ONLY

turn the measuring cup clockwise as far as it

will go.

BEFORE USING THE UNIT

• Insert the power plug into the mains socket.

After unit transportation or storage at low

Note: The blender will not be switched on if the

temperature keep it for at least three hours

blender bowl (3) is installed incorrectly.

at room temperature before switching on.

• Use the operation mode switch (7) to set the

• Unpack the unit completely and remove any

required rotation speed of the knives:

stickers that can prevent unit operation.

– «I» (low speed) - for mixing liquid products;

• Check the unit for damages; do not use it in

– «II» (high speed) - for liquid and hard prod-

case of damages.

ucts.

• Before switching the unit on, make sure that

• To switch the pulse mode on, set the switch

your home mains voltage corresponds to the

(7) to the position “P” and hold it for several

unit operating voltage.

seconds.

• Before the first use wash all removable parts

• During the operation or between the opera-

with warm water and neutral detergent and

tion cycles, you can add the required ingre-

then dry thoroughly.

dients into the bowl (3). To this end, turn the

• Clean the motor unit with a soft, slightly damp

measuring cup (1) counterclockwise, match-

cloth and then wipe it dry.

ing the corresponding marks, and remove the

• Do not immerse the motor unit into any

measuring cup (1). After adding ingredients

liquids or wash it with water.

through the lid (2) opening, install the mea-

• Place the blender on a flat stable surface.

suring cup (1) back to its place.

ATTENTION! Continuous operation time of

• After the unit’s operation is finished, set the

the blender should not exceed 2 minutes;

operation mode switch (7) to the “0” position

then switch the unit off and let it cool down

and unplug the unit.

for at least 2 minutes.

• Remove the blender bowl (3) from the motor

• Do not remove the blender bowl and the bowl

unit (6) by turning it counterclockwise.

lid during the operation.

• Remove the measuring cup (1) from the lid

(2).

USING THE BLENDER

• Remove the lid (2) from the bowl (3) taking it

• Place the blender bowl (3) on the motor unit

by the ledge and take the processed products

(6) and turn it clockwise until bumping.

out of the bowl (3). If necessary, you can use a

• Remove the blender bowl lid (2).

spatula to remove the products.

• Put the necessary ingredients into the

• After the operation is finished, wash the

bowl (3).

blender bowl (3).

Note:

Note:

– Before starting to chop/mix, we recommend

– If food processing is hard, add some liquid

to peel fruit, remove inedible parts, such as

(water, liquor, juice) into the blender bowl (3).

stones, and cut fruit into cubes approximately

– To chop ice cubes (no more than 10 cubes

2х2 cm in size.

sized 2.5 cm x 2.5 cm x 2.5 cm) put them

VT-8517.indd 4 17.02.2016 17:19:54