Vitek VT-8103 B: Vacuum cleaner body STORAGE DELIVERY SET TECHNICAL SPECIFICATIONS Cleaning the brush block (1) Guarantee

6

Cleaning the filters (13, 14), the dust bin (5) flask

Vacuum cleaner body

–

Holding the dust bin (5) by the handle press the

•

Clean the vacuum cleaner body with a soft, slightly

button (9) and remove the dust bin (5) from the unit

damp cloth and then wipe it dry.

body holding the vacuum cleaner by the handle

•

Do not immerse the body of the vacuum cleaner,

(10) (pic. 4).

the power cord and the power plug of the unit into

–

Remove the inlet foam filter (13) from the unit body.

water or any other liquids. Provide that no liquid

–

Place the dust bin (5) above the garbage bin. Open

gets inside the vacuum cleaner body.

the lower lid of the dust bin flask by pressing the lid

•

Never use solvents or abrasives to clean the sur-

clamp (3). Remove accumulated dust and waste

face of the vacuum cleaner.

from the dust bin (5) (pic. 6).

–

Open the upper lid of the dust bin by pulling the lid

STORAGE

clamp (7) and remove the outlet filter (14) (pic. 7).

The vertical vacuum cleaner VT-8103 occupies very

–

Close the upper lid of the dust bin (5) by pulling the

little space due to its upright configuration. Its width

lid clamp (7).

and length are only 27 and 21 cm respectively. Special

–

Wash the filters (13 and 14) under warm water jet

cord storage hooks on the unit body and the clip on the

and dry them thoroughly.

handle (10) secure the cord properly and do not allow it

–

Install the inlet foam filter (13) back to its place.

to fall down and unwind.

–

Take the dust bin (5) by the handle and rotate it

•

Before taking the vacuum cleaner away for long

counterclockwise in the direction of the symbol

term storage, clean its body, the dust bin (5) flasks,

holding the dust bin by the flask. Remove the dust-

the dustbag (15), the filters (13, 14) and the brush

bag (15) from the dust bin (5) flask, wash it under

block (1).

warm water jet and dry it.

•

Keep the vacuum cleaner away from children in a

–

Wash the dust bin (5) flask under warm water jet

dry cool place.

and then dry it.

–

Install the dustbag (15) into the dust bin (5) flask

DELIVERY SET

matching the corresponding guidelines of the dust-

1.

Vacuum cleaner with the filters

bag (15) with the grooves inside the flask, hold the

and the dust bin installed – 1 pc.

flask and turn the dust bin handle clockwise in the

2.

Handle – 1 pc.

direction of the symbol

(pic. 8) until locking.

3.

Floor/carpet brush – 1 pc.

Note: Note that when you’re installing the dustbag

4.

Manual – 1 pc.

(15) the symbols

/ on the dust bin (5) flask should

be on the button (9) side.

TECHNICAL SPECIFICATIONS

–

Open the upper lid of the dust bin (5) by pulling the

Power supply: 220-240 V ~ 50 Hz

lid clamp (7) and install the outlet filter (14).

Power consumption: 1800 W

Suction power: 350 W

Cleaning the brush block (1)

–

It is also recommended to clean the roller brush as

The manufacturer preserves the right to change the

it becomes dirty. To do this remove the brush block

specifications of the unit without a preliminary noti-

(1) by pressing the button (2) and pulling the unit

fication.

body upwards (pic. 2), slightly press on the brush

block (1) with your foot to keep it on the floor.

Unit operating life is 3 years

–

Turn the brush block (1) upside down. Insert a coin

or a flat head screwdriver into the roller brush lock

Guarantee

(16) groove and turn it in the direction of the sym-

Details regarding guarantee conditions can be ob-

bol

. Remove the roller brush lock (16) from the

tained from the dealer from whom the appliance was

brush block (1) and remove the roller brush (17)

purchased. The bill of sale or receipt must be pro-

(pic. 9).

duced when making any claim under the terms of this

–

Clean the roller brush (17).

guarantee.

Note: Do not wash the roller brush (17) with water.

–

After cleaning install the roller brush (17) back to

This product conforms to the EMC-

its place and install the lock (16). Insert a coin or a

Requirements as laid down by the Council

flat head screwdriver into the roller brush lock (16)

Directive 2004/108/ЕС and to the Low Voltage

groove and turn it in the direction of the symbol

.

Regulation (2006/95/ЕС)

IM VT-8103.indd 6 31.05.2016 16:13:52