Vitek VT-8103 B: USING THE VACUUM CLEANER SAFETY MEASURES CLEANING THE VACUUM CLEANER

5

if they are not under supervision of a person who

Installing and removing the dust bin (5)

is responsible for their safety or if they are not

–

Before installing the dust bin make sure that the

instructed by this person on the usage of the unit.

inlet (foam) filter (13) and the outlet filter (14) of

•

Do not leave children unattended to prevent using

the dust bin are installed properly. The outlet filter

the unit as a toy.

(14) should be installed in the dust bin (5) and the

•

For children safety reasons do not leave polyethyl-

clamps (3, 7) of lower and upper lids of the dust bin

ene bags, used as packaging, unattended.

should be closed.

Attention! Do not allow children to play with polyethyl-

–

Install the dust bin (5) with the installed outlet fil-

ene bags or packaging film. Danger of suffocation!

ter (14) on the unit body (pic. 3). If the dust bin is

•

Transport the unit in the original package only.

installed properly you will hear a click.

•

Regularly check the power plug and power cord

–

To remove the dust bin (5) press the release but-

integrity for damages.

ton (8) and remove the dust bin (5) from the unit

•

Never use the unit if the power cord or the power

body holding the vacuum cleaner by the handle

plug is damaged, if the unit works improperly, after

(10) (pic. 4).

it was dropped or in case of leakage.

•

Do not attempt to repair the unit. Do not disas-

Installing and removing the handle (10)

semble the unit by yourself, if any malfunction is

–

Before installing turn the handle (10) so the groove

detected or after it was dropped, unplug the unit

in the lower part of the handle is directed towards

and apply to any authorized service center from the

the dust bin (5).

contact address list given in the warranty certificate

–

Press on the clamp (8) and insert the handle (10) into

and on the website www.vitek.ru.

the corresponding opening in the unit body (pic. 5).

•

Keep the unit out of reach of children and disabled

If the handle is installed properly you will hear a click.

persons.

–

To remove the handle (10) press on the clamp (8)

and pull the handle upwards, holding the unit body.

THE UNIT IS INTENDED FOR HOUSEHOLD USAGE ONLY

USING THE VACUUM CLEANER

SAFETY MEASURES

ATTENTION! Always switch the vacuum cleaner on only

•

Do not use the vacuum cleaner near hot surfaces,

with the dust bin (5) and inlet foam (13) and outlet (14)

ashtrays and in places where inflammable liquids

filters installed. Before switching the vacuum cleaner on

are stored.

always make sure that the filters are installed properly.

•

Take sharp objects away from the floor before

–

Before using the unit, unwind the power cord to its

cleaning to prevent unit damage.

full length and insert the power plug into the mains

socket.

ASSEMBLING THE VACUUM CLEANER

Note: You can adjust the power cord length, if neces-

After unit transportation or storage at low temper-

sary. Special cord storage hooks on the unit body and

ature keep it for at least three hours at room tem-

the clip on the handle (10) secure the cord and will not

perature before switching on.

allow it to fall down and unwind.

–

Unpack the unit completely and remove any stick-

–

Slightly press on the brush block (1) with your foot

ers that can prevent unit operation.

and tilt the vacuum cleaner body from the vertical

–

Check the unit for damages; do not use it in case

(storage) position.

of damages.

Note: The roller brush (17) does not rotate in the stor-

–

Before switching the unit on, make sure that your

age position.

home mains voltage corresponds to the unit oper-

–

Press the ON/OFF button (6) to switch the vacuum

ating voltage.

cleaner on.

–

After room cleaning press the ON/OFF button (6),

Installing and removing the floor/

set the vacuum cleaner to the storage position and

carpet brush block (1)

unplug it.

–

Place the brush block (1) on the floor. Match the

–

To wind and fix the power cord use the cord storage

setting opening (12) in the unit body with the setting

(4) and the clip on the handle (10).

nozzle (11) of the brush block (1). Insert the brush

block (1) into the unit body until clicking (pic. 1).

CLEANING THE VACUUM CLEANER

–

To remove the brush block (1) press the button

It is recommended to clean the vacuum cleaner after

(2) and pull the unit body upwards (pic. 2), slightly

every use. Before cleaning the unit, switch it off by

pressing on the brush block with your foot to keep

pressing the button (6), set the vacuum cleaner to the

it on the floor.

storage position and unplug it.

IM VT-8103.indd 5 31.05.2016 16:13:52