Vitek VT-1468 BD: USING THE WHISK USING THE CHOPPER

5

ATTENTION!

ATTENTION!

– Do not remove the blender attachment (1)

Do not chop very hard products, such as ice

during operation.

cubes, nutmegs, coffee beans, cereals etc.

– To avoid damage to the blades, do not

Before you start chopping:

process too hard products such as cere-

– Cut meat, cheese, onions, vegetables and

als, rice, spices, coffee beans, cheese,

fruit into pieces approximately 2x2 cm in size.

frozen foods.

– Remove stems of herbs, shell nuts.

– If the foodstuffs are hard to chop with the

– Remove bones, sinews and cartilage from

blender attachment, add some liquid if

meat.

possible.

– To achieve the best results refer to the table

below.

USING THE WHISK

Use the whisk attachment (11) only for beating

Approximate

Weight,

cream and egg whites, making biscuit dough or

Product type

processing

g

for mixing ready desserts.

time, seconds

WARNING: Before assembling make sure

Meat 250 8-10

that the power plug is not inserted into the

mains socket.

Herbs 50 8-10

• Insert the whisk attachment (11) into the whisk

Nuts 100 8-10

gear (12).

• Insert the whisk gear (12) into the motor unit

Cheese 100 5-7

(2), having preliminary matched the corre-

Bread 5-7 5-7

sponding marks, and turn it clockwise until

it is fixed.

Onions (cut into

150 8-10

• Insert the power plug into the mains socket.

several pieces)

• Put the whisk attachment (11) into the bowl

Cookies 150 6-8

with products.

Note: You can put the products into the mea-

Soft fruit 200 6-8

suring cup (10), placing it on the rubberized

base (9).

Chopping

• Set the required operation speed with the

Be careful – the knife is very sharp! Always

control knob (5).

hold the knife by the upper plastic end.

• To switch the unit on, press and hold down the

• Place the chopper bowl (6) on a flat stable

ON/OFF button «I» (4).

surface.

• If you press and hold down the button «II»

• Set the chopping knife (7) on the axis inside

(3), the unit will operate at maximum rota-

the chopper bowl (6).

tion speed.

• Put the products into the chopper bowl (6).

• After you finish using the unit, take the

Note:

power plug out of the mains socket, discon-

– Do not switch the unit on when the chopper

nect the whisk gear (12) from the motor unit

bowl (6) is empty.

(2) by turning it counterclockwise and then

• Place the geared lid (8) on the chopper bowl

remove the whisk attachment (11) from the

(6) and rotate it clockwise until it is fixed.

gear (12).

• Install the motor unit (2) on the lid (8) feeding

ATTENTION!

chute, having preliminary matched the corre-

– Do not use the whisk attachment (11) to knead

sponding marks, and turn it clockwise until it

tight dough.

is fixed. Install the motor unit strictly in a ver-

– Put products into the bowl before switching

tical position, evenly and in secure contact

the unit on.

with the lid.

– To connect the unit to the mains, insert the

USING THE CHOPPER

power cord plug into the mains socket.

The chopper is used to chop meat, cheese,

– Set the required speed with the control knob (5).

onion, herbs, garlic, carrots, walnuts, almonds,

– To switch the unit on, press and hold down the

prunes, vegetables and fruit.

ON/OFF button «I» (4).

VT-1468.indd 5 08.02.2016 10:23:43