Vitek VT-4036 BN: SYSTEM OPERATION A. TURNING THE POWER ON / OFF G. AUDIO SOURCE SELECTION  2.1 CH or 5.1 CH H. MUTE FUNCTION B. VOLUME I. AM/FM TUNER C. 3D SOUND MODE D. CENTER SPEAKER E. REAR SPEAKERS RESOLVING MALFUNCTIONS F. FRONT SPEAKERS 2. NO SOUND IS COMING FROM THE FRONTLEFT SPEAKER

ENGLISH

SYSTEM OPERATION

decrease the volume level on the front speakers; the dis

A. TURNING THE POWER ON / OFF

play on the front panel will show the volume level of the

1. Make all the necessary connections in accordance with

front speakers in a numerical format.

the setup instructions before turning on the device.

2. Connect the system’s power cord to an electrical outlet.

G. AUDIO SOURCE SELECTION  2.1 CH or 5.1 CH

(ATTENTION: The power source should conform to the

1. Connect the system correctly to the audio source.

device’s power supply requirements).

2. Press the CD/DVD button on the remote control unit or

3. Set the power switch, located on the rear panel of the

on the front panel of the subwoofer to select the audio

device, to the ON position. Press the STANDBY button,

source (2.1 CH or 5.1 CH).

located on the remote control unit or on the front panel

of the device, to turn on the device’s power.

H. MUTE FUNCTION

1. Press the MUTE button on the front panel or on the

B. VOLUME

remote control unit to turn off the sound.

1. Press the VOL + button on the remote control unit to

2. The MUTE indicator will appear on the front of the sub

increase the overall system volume; the display on the

woofer.

front panel will show the overall volume level of the sys

3. Press the MUTE button again to turn on the sound.

tem in a numerical format.

2. Press the VOL – button on the remote control unit to

I. AM/FM TUNER

decrease the overall system volume; the display on the

Connect the AM and FM antennas to their respective

front panel will show the overall volume level of the sys

jacks located on the rear panel of the subwoofer.

tem in a numerical format.

1. Press the INPUT button on the remote control unit or on

the front panel until the subwoofer’s display shows the

C. 3D SOUND MODE

“TUNE” indicator.

1. Connect the center and rear speakers to the system.

3. Use the FM/AM button located on the remote control unit

2. Press the 3D button located on the remote control unit to

to choose the desired band (FM or AM).

turn the 3D sound on or off.

4. Press the SCAN button on the remote control unit to acti

vate the automatic tuning function. The tuner will tune to

D. CENTER SPEAKER

a radio station automatically.

1. Press the CEN + button on the remote control unit to

5. Press the TUNE+ or TUNE button on the remote control

increase the volume level on the central speaker; the dis

unit to tune to a radio station manually.

play on the front panel will show the volume level of the

6. Press the ST/MN button on the remote control unit while

central speaker in a numerical format.

in the FM band to choose between stereo and mono

2. Press the CEN – button on the remote control unit to

modes.

decrease the volume level on the central speaker; the

7. To save a chosen radio station into memory, press the

display on the front panel will show the volume level of

MEMORY button on the remote control unit and then

the central speakers in a numerical format.

press the desired memory location number on the

numeric keypad and the station will be saved into memo

E. REAR SPEAKERS

ry. To enter a number of ten or higher, first press the 10+

1. Press the REAR + button on the remote control unit to

button and then a numeric button from 09.

increase the volume level on the rear speakers; the dis

NOTE: You can save up to 20 radio stations into memory.

play on the front panel will show the volume level of the

rear speakers in a numerical format.

RESOLVING MALFUNCTIONS

2. Press the REAR – button on the remote control unit to

1. THERE IS NO SOUND AT ALL

decrease the volume level on the rear speakers; the dis

(1) Make sure the system is connected properly.

play on the front panel will show the volume level of the

(2) Increase the volume.

rear speakers in a numerical format.

(3) Make sure the audio input is selected properly.

(4) Make sure the MUTE function has not been activated.

F. FRONT SPEAKERS

1. Press the FRONT + button on the remote control unit to

2. NO SOUND IS COMING FROM THE FRONTLEFT SPEAKER

increase the volume level on the front speakers; the dis

(1) Make sure the frontleft speaker is properly connected to

play on the front panel will show the volume level of the

the device.

front speakers in a numerical format.

(2) Make sure the device is properly connected to the audio

2. Press the FRONT – button on the remote control unit to

source.

6