Vitek VT-3624: REMOVING THE FRONT PANEL MASKING OF ALTERNATIVE FREQUENCIES RETUNING STATIONS (L / S) (2) 1. POWER ON/OFF 2,3. MENU SETTINGS BUTTONS: BASS/TRE- AUDIO PROCESSOR (AUDIO DSP) (2) TRAFFIC ANNOUNCEMENTS (TA SEEK /TA ALARM) (2) TONE COMPENSATION (LOUDNESS) (2)

ENGLISH

Removal and installation of the front panel

transmitting traffic information and sounds a

The front panel of this device can be removed in

warning beep before the beginning of the traffic

order to avoid theft.

information broadcast.

REMOVING THE FRONT PANEL

MASKING OF ALTERNATIVE FREQUENCIES

Before removing the decks front panel, turn off

(MASK DPI) (2)

the power by pressing button (1)POWER

Holding down the SEL button for more than 2

ON/OFF (PWR).

seconds activates the selection of alternative

Press the panel release button 14 to remove the

frequencies processing mode.

front panel (REL), pull the panel towards your-

self.

See the figure (5,6,7,8).

Notes:

MASK DPI mode: masks radio stations on

 Do not press too hard when installing the panel.

alternative radio frequencies (AF) that have dif-

It freely snaps into place with light pressure.

fering program identifiers (PI).

 When taking the panel with you, place it in the

MASK ALL mode: masks radio stations on

supplied case.

alternative radio frequencies with differing pro-

 Do not press hard on the LCD screen when con-

gram identifiers and no RDS signal.

necting the front panel to the main unit.

RETUNING STATIONS (L / S) (2)

1. POWER ON/OFF

Pressing the SEL button for more than 2 sec-

Press this button to turn the device on. To turn it

onds activates the function selector for the

off, press and hold this button for more than 1

retune mode, which retunes to stations transmit-

second. This device turns on when any button is

ting traffic information.

pressed.

RETUNE L: Sets the TA search mode delay to

90 seconds.

2,3. MENU SETTINGS BUTTONS: BASS/TRE-

RETUNE S: Set the TA search mode delay to 30

BLE/CHANNEL BALANCE/ FADER

seconds.

When pressed momentarily, the sound charac-

teristics setting mode is activated.

VOLUME- BASS TREBLE CHANNEL

BALANCE FADER VOLUME

AUDIO PROCESSOR (AUDIO DSP) (2)

Rotate knob 3 to set the desired parameters

Pressing the SEL button for more than 2 sec-

VOLUME, BASS, TREBLE, CHANNEL BALANCE,

onds activates the function selector for the

FADER.

audio processing parameters.

TRAFFIC ANNOUNCEMENTS (TA SEEK /TA

ALARM) (2)

Press the SEL button for more than 2 seconds to

activate the function selector for traffic notifica-

The parameters are chosen using the 3 (VOL)

tion messages.

knob in the following order:

The TA SEEK or TA ALARM functions can be

POP M-ROCK M-CLASSICAL- NEUTRAL

chosen by rotating the VOL knob.

MUSIC-PROCESSOR OFF

TONE COMPENSATION (LOUDNESS) (2)

Pressing the SEL button for more than 2 sec-

 TA SEEK mode:

onds activates the high and low frequencies

If a newly tuned station does not transmit traffic

amplification mode.

information within 5 seconds, the radio automat-

ically tunes to the next station that transmits

traffic information. In TA search mode, the cur-

rent station can be switched to another station if

the signal is lost or the station stops broadcast-

The LOUD ON/OFF mode is chosen by rotating

ing traffic information, because the device is

the 3 (VOL) knob.

searching for other stations, broadcasting traffic

information, that have strong broadcast signals

and are transmitting TP-signal information.

 TA ALARM mode:

This mode automatically switches to a station

5