Fein WSB-14-125T: en For your safety.

16

en For your safety.

Read all safety warnings and all instruc-

tions. 

Failure to follow the warnings 

and instructions may result in electric 

shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

Do not use this power tool before you have thor-

oughly read and completely understood this 

Instruction Manual and the enclosed “General 

Safety Instructions” (document number 

3 41 30 054 06 1). The documents mentioned should be 

kept for later use and enclosed with the power tool, 

should it be passed on or sold.

Please also observe the relevant national industrial safety 

regulations.

Safety Warnings common for Grinding, Sanding, Wire 

Brushing or Abrasive Cutting Off Operations

This power tool is intended to function as a grinder, sander, 

wire brush or cut-off tool. Read all safety warnings, instruc-

tions, illustrations and specifications provided with this 

power tool.

 Failure to follow all instructions listed below 

may result in electric shock, fire and/or serious injury.

This power tool is not recommended for polishing.

 Opera-

tions for which the power tool was not designed may 

create a hazard and cause personal injury.

Do not use accessories which are not specifically designed 

and recommended by the tool manufacturer.

 Just because 

the accessory can be attached to your power tool, it does 

not assure safe operation.

The rated speed of the accessory must be at least equal to 

the maximum speed marked on the power tool.

 Accessories 

running faster than their rated speed can break and fly 

apart.

The outside diameter and the thickness of your accessory 

must be within the capacity rating of your power tool.

Incorrectly sized accessories cannot be adequately 

guarded or controlled.

The arbor size of wheels, flanges, backing pads or any other 

accessory must properly fit the spindle of the power tool.

Accessories with arbor holes that do not match the 

mounting hardware of the power tool will run out of bal-

ance, vibrate excessively and may cause loss of control.

Do not use a damaged accessory. Before each use inspect 

the accessory such as abrasive wheels for chips and 

cracks, backing pad for cracks, tear or excess wear, wire 

brush for loose or cracked wires. If power tool or accessory 

is dropped, inspect for damage or install an undamaged 

accessory. After inspecting and installing an accessory, 

position yourself and bystanders away from the plane of the 

rotating accessory and run the power tool at maximum no-

load speed for one minute.

 Damaged accessories will nor-

mally break apart during this test time.

Wear personal protective equipment. Depending on appli-

cation, use face shield, safety goggles or safety glasses. As 

appropriate, wear dust mask, hearing protectors, gloves 

and workshop apron capable of stopping small abrasive or 

workpiece fragments.

 The eye protection must be capable 

of stopping flying debris generated by various operations. 

The dust mask or respirator must be capable of filtrating 

particles generated by your operation. Prolonged expo-

sure to high intensity noise may cause hearing loss.

Keep bystanders a safe distance away from work area. Any-

one entering the work area must wear personal protective 

equipment.

 Fragments of workpiece or of a broken acces-

sory may fly away and cause injury beyond immediate 

area of operation.

Hold power tool by insulated gripping surfaces only, when 

performing an operation where the cutting accessory may 

contact hidden wiring or its own cord.

 Cutting accessory 

contacting a “live” wire may make exposed metal parts of 

the power tool “live” and shock the operator.

Position the cord clear of the spinning accessory.

 If you 

lose control of the power tool, the cord may be cut or 

snagged and your hand or arm may be pulled into the 

spinning accessory.

Never lay the power tool down until the accessory has come 

to a complete stop.

 The spinning accessory may grab the 

surface and pull the power tool out of your control.

Character

Unit of measure, 

international

Unit of measure, 

national

Explanation

n

/min

rpm

Rated speed

P

1

W

W

Power input

P

2

W

W

Output

M…

mm

mm

Size of metric thread

L

wA

dB

dB

Sound power level

L

pA

dB

dB

Sound pressure level

K…

Uncertainty

m/s

2

m/s

2

Acceleration

m, s, kg, A, mm, V, 

W, Hz, N, °C, dB, 

/min, m/s

2

m, s, kg, A, mm, V, 

W, Hz, N, °C, dB, 

rpm, m/s

2

Basic and derived units of measure from the inter-

national system of units 

SI

.

WARNING

3 41 01 104 06 0.book  Seite 16  Mittwoch, 2. Juli 2008  1:43 13