Milwaukee PDD 14.4X: 16 17 ENGLISH ENGLISH

16 17 ENGLISH ENGLISH: Milwaukee PDD 14.4X

TECHNICAL DATA

PDD 12 PDD 12 X PDD 14.4 PDD 14.4 X

EC-DECLARATION OF CONFORMITY

SYMBOLS

Drilling capacity in steel ...........................................................

...........13 mm.............. 13 mm .............. 13 mm ............13 mm

We declare under our sole responsibility that this product is

Drilling capacity in wood ..........................................................

...........34 mm.............. 34 mm .............. 36 mm ............36 mm

in conformity with the following standards or standardized

Please read the instructions carefully

Wood screws (without pre-drilling) ..........................................

.......8x80 mm.......... 8x80 mm ........ 10x50 mm ...... 10x50 mm

documents.

before starting the machine.

-1

-1

-1

-1

No-load speed, 1st gear ..........................................................

......0-400 min

....... 0-400 min

.......0-480 min

......0-480 min

EN 60745-1:2009 + A11:2010

-1

-1

-1

-1

No-load speed, 2nd gear .........................................................

....0-1300 min

..... 0-1300 min

.....0-1500 min

....0-1500 min

EN 60745-2-1:2010

Torque

EN 55014-1:2006 + A1:2009 + A2:2011

Low torque*1 ........................................................................

...........22 Nm .............. 22 Nm ..............26 Nm .............26 Nm

EN 55014-2:1997 + A1:2001 + A2:2008

Accessory - Not included in standard

High torque*1 ........................................................................

...........50 Nm .............. 50 Nm ..............60 Nm .............60 Nm

in accordance with the regulations

equipment, available as an accessory.

Static jamming moment, 1st gear/2nd gear *1 .....................

......31/10 Nm ......... 31/10 Nm .........40/16 Nm ........40/16 Nm

2011/65/EU (RoHs)

Screwing capacity with one fully charged battery (2.4 Ah) : *2

2006/42/EC

5x40 Soft wood ....................................................................

............370 .....................370 ................530 .................. 530

2004/108/EC

Drilling capacity with one fully charged battery (2.4 Ah):*2

ø 3 mm Steel plate 1,5 mm ..................................................

............350 .....................350 ................420 .................. 420

Remove the battery pack before starting any

ø 6 mm Soft wood 40 mm ....................................................

............320 .....................320 ................400 .................. 400

work on the machine.

Battery voltage.........................................................................

...........12 V ................. 12 V...............14,4 V ............. 14,4 V

Winnenden, 2012-09-11

Drill opening range ..................................................................

.....1,5-13 mm........1,5-13 mm ........1,5-13 mm ......1,5-13 mm

Weight according EPTA-Procedure 01/2003 with chuck .........

..........2,1 kg ............... 2,3 kg ...............2,3 kg .............2,5 kg

Weight according EPTA-Procedure 01/2003 without chuck ....

............... ................... 1,9 kg .................... .................2,1 kg

Do not dispose of electric tools together with

household waste material! In observance of

Noise/vibration information

Rainer Kumpf

European Directive 2002/96/EC on waste

Measured values determined according to EN 60 745.

Director Product Development

electrical and electronic equipment and its

Typically, the A-weighted noise levels of the tool are:

Authorized to compile the technical le

implementation in accordance with national

Sound pressure level (K = 3 dB(A)) .......................................

........< 73 dB (A) ...... < 73 dB (A) ....... < 70 dB (A) ..... < 70 dB (A)

law, electric tools that have reached the end of

The noise level when working can exceed 85 dB (A).

SPECIFIED CONDITIONS OF USE

their life must be collected separately and

Wear ear protectors!

returned to an environmentally compatible

The battery screwdriver is designed for drilling and

recycling facility.

screwdriving for independent use away from mains supply.

Total vibration values (vector sum in the three axes)

Do not use this product in any other way as stated for

determined according to EN 60745.

normal use.

Vibration emission value ah

2

Drilling into metal ..................................................................

.......< 2,5 m/s

2

ADVICE FOR OPERATION

Uncertainty K ........................................................................

..........1,5 m/s

2

Screwing ...............................................................................

.......< 2,5 m/s

The gears can be only changed when the machine is

2

Uncertainty K ........................................................................

..........1,5 m/s

switched off.

*1 Measured according to Milwaukee norm N 877318

BATTERIES

*2 The values stated are reference values. Actual values might differ, depending on the material and quality of the screws.

New battery packs reach full loading capacity after 4 - 5

chargings and dischargings. Battery packs which have not

been used for some time should be recharged before use.

WARNING

Temperatures in excess of 50°C (122°F) reduce the

performance of the battery pack. Avoid extended exposure

The vibration emission level given in this information sheet has been measured in accordance with a standardised test given

to heat or sunshine (risk of overheating).

in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.

The contacts of chargers and battery packs must be kept

The declared vibration emission level represents the main applications of the tool. However if the tool is used for different

clean.

applications, with different accessories or poorly maintained, the vibration emission may differ. This may signicantly increase

the exposure level over the total working period.

For an optimum life-time, after use, the battery packs have

to be fully charged.

An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or

when it is running but not actually doing the job. This may signicantly reduce the exposure level over the total working period.

To obtain the longest possible battery life remove the battery

pack from the charger once it is fully charged.

Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the

accessories, keep the hands warm, organisation of work patterns.

For battery pack storage longer than 30 days:

Store the battery pack where the temperature is below 27°C

and away from moisture

Store the battery packs in a 30% - 50% charged condition

Remove the battery pack before starting any work on the

Every six months of storage, charge the pack as normal.

WARNING! Read all safety warnings and all

machine.

instructions, including those given in the accompanying

brochure. Failure to follow the warnings and instructions

Do not dispose of used battery packs in the household

MAINTENANCE

may result in electric shock, re and/or serious injury.

refuse or by burning them. Milwaukee Distributors offer to

Use only Milwaukee accessories and spare parts. Should

Save all warnings and instructions for future reference.

retrieve old batteries to protect our environment.

components need to be replaced which have not been

Do not store the battery pack together with metal objects

described, please contact one of our Milwaukee service

SAFETY INSTRUCTIONS

(short circuit risk).

agents (see our list of guarantee/service addresses).

Wear ear protectors. Exposure to noise can cause hearing

Use only System PBS 3000 chargers for charging System

If needed, an exploded view of the tool can be ordered.

loss.

PBS 3000 battery packs. Do not use battery packs from

Please state the Article No. as well as the machine type

other systems.

printed on the label and order the drawing at your local

Hold power tool by insulated gripping surfaces, when

service agents or directly at: Milwaukee Electric Tool,

performing an operation where the cutting accessory

No metal parts must be allowed to enter the battery section

Max-Eyth-Straße 10, D-71364 Winnenden, Germany.

may contact hidden wiring or its own cord. Contact with

of the charger (short circuit risk).

a „live“ wire will also make exposed metal parts of the power

Never break open battery packs and chargers and store

tool „live“ and shock the operator.

only in dry rooms. Keep dry at all times.

Always wear goggles when using the machine. It is

Battery acid may leak from damaged batteries under

recommended to wear gloves, sturdy non slipping shoes

extreme load or extreme temperatures. In case of contact

and apron.

with battery acid wash it off immediately with soap and

Sawdust and splinters must not be removed while the

water. In case of eye contact rinse thoroughly for at least 10

machine is running.

minutes and immediately seek medical attention.

When working in walls ceiling, or oor, take care to avoid

electric cables and gas or waterpipes.

16 17

ENGLISH ENGLISH