Binatone SI-2510: CARE AND MAINTENANCE
CARE AND MAINTENANCE: Binatone SI-2510
Burst of steam in a vertical position
This function helps to freshen the appearance of curtains, jackets,
coats, etc. To use this function, take the following steps:
Follow instructions in paragraph 1-4 of the section “Operation
instructions”. While selecting the temperature setting, put the
temperature control knob (10) into the “Max” position.
While holding the iron in a vertical position, aim its sole plate
towards the articles to be ironed and push the steam burst button
ENGLISH
(8) to produce a directional strong burst of steam from the sole
plate. Push the button several times with 5-7 seconds intervals
until the article is fully refreshed. If during the process your water
tank (5) runs out of water, disconnect the appliance from the
mains outlet, wait till it cools down, refill the tank and plug the
appliance back into the power supply and continue the process.
Spray
Using the water spray (7) will help when ironing details of the
article (cuffs, trimmings, plackets, etc) or clothes, which demand “•“
(low temperature) ironing, when steam ironing is not possible. Push
the button several times to moisten the material.
5. When you have finished cleaning or ironing, do not forget to switch
the iron off by putting the steam control knob (9) into the “0“
position, the temperature control knob (10) — into the “Min“
position and unplugging the appliance from the mains supply outlet.
CARE AND MAINTENANCE
Cleaning of the sole plate
The scale on the sole plate can be removed with
a rough cotton cloth dampened with a vinegar
solution.
Do not use any abrasive substances and
materials to clean the sole plate.
Cleaning of internal parts of the appliance
In areas with hard water it is recommended that you regularly
remove scale from the appliance to maintain it in good working order.
Excess lime scale may result in damage or malfunction of your product.
If in your area the water is soft and you have average amounts of
clothes to be ironed then we recommend you to de-scale every 6
months. If the water in your area is very hard or if you iron frequently,
then we recommend you de-scale once a month.
Your iron has a self-cleaning function, which allows you to clean
the internal parts of the appliance from scale or dust. To use this function
perform the following procedure:
1. Set the steam control knob (9) into the “0” position.
2. Fill the tank (5) with water to the “Max” level.
3. Place the iron in a vertical position and plug it into the mains supply
outlet.
4. Set the temperature control knob (10) into the “Max” position.
The light indicator (11) will light up showing that the iron is being
heated to the desired temperature.
5. When the iron reaches the maximum temperature, the light
indicator (11) will go out.
6. Whilst holding the appliance horizontally over a sink, set the steam
control knob (9) into the “Self-Clean” position. Hot steam will
7
Оглавление
- Steam Iron
- SAFETY MEASURES
- SPECIAL SAFETY MEASURES
- INSTRUCTIONS FOR USE
- CARE AND MAINTENANCE
- USEFUL TIPS
- DISPOSAL
- MESURES DE SECURITE
- MESURES SPECIALES DE SECURITE
- AVANT L’UTILISATION
- ENTRETIEN ET NETTOYAGE
- CONSEILS UTILES
- RECYCLAGE
- ÌÅÐÛ ÁÅÇÎÏÀÑÍÎÑÒÈ
- ÑÏÅÖÈÀËÜÍÛÅ ÌÅÐÛ ÁÅÇÎÏÀÑÍÎÑÒÈ
- ÏÅÐÅÄ ÈÑÏÎËÜÇÎÂÀÍÈÅÌ
- ÓÕÎÄ È ×ÈÑÒÊÀ
- ÏÎËÅÇÍÛÅ ÑÎÂÅÒÛ
- ÓÒÈËÈÇÀÖÈß
- ÏÐÀÂÈËÀ ÁÅÇÏÅÊÈ
- ÑÏÅÖ²ÀËÜͲ ÏÐÀÂÈËÀ ÁÅÇÏÅÊÈ
- ÏÅÐÅÄ ÂÈÊÎÐÈÑÒÀÍÍßÌ
- ÄÎÃËßÄ ÒÀ ×ÈÙÅÍÍß
- ÊÎÐÈÑͲ ÏÎÐÀÄÈ
- ÓÒÈ˲ÇÀÖ²ß