Binatone EEJ-1555 B-QUICK: USEFUL ADVICE

Removing water out of the appliance

1. Press the lid release button (4).

2. Hold your appliance over a sink. Then, tip your appliance

upside down (see fig. B,C).

3. Still holding your appliance over the sink, turn it the right side

up and allow any water to drain out of the dispensing nozzle

(9). See fig. D.

4. Repeat steps 2 and 3 until the water has been emptied from

your appliance.

5. Store the appliance only after its parts are completely dry.

Attention: if your appliance will not be used for an

extended period (e.g. if you are on holiday), we

recommend that you first empty it. Before using your

Appliance again, carry out several boil cycles

discarding the water each time.

USEFUL ADVICE

In regions with high water hardness it is neces-

sary to remove scale from the appliance regularly

to keep it in good working order, since excessive

scale in the appliance may cause its incorrect op-

eration or breakdown.

Frequency of cleaning depends on the degree

of tap water hardness in your region and on fre-

quency of the appliance use. If water in your house is hard, we

recommend filtering it – it will decrease scale deposit.

Warning: to extend working life of the appliance, de-scale it

not less than once per three months.

De-scaling the appliance

1. Check the correct positioning of the appliance (see the section

«INSTRUCTIONS ON USE», points 1-3).

2. Fill your appliance to the MAX fill level and place an empty cup

on the drip tray (8).

3. Set the on/off switch (2) to the on position and wait for the

water to be dispensed into the cup.

4. Add a citric acid-based proprietary descaling product to the

hot water in the cup and stir.

5. Open the cover (3) by pressing the button (4) and pour the

content of the cup into the water container (5). Close the

cover.

6. Place the empty cup on the drip tray (8) and set the on/off

switch to the on position.

7. Wait for the water to be dispensed into the cup.

8. Discard the water from the cup.

9. Repeat steps 6, 7 and 8 until the water level is at the MIN

mark. Open the lid and empty any remaining water into the

sink. Rinse your appliance by filling it with clean water and

emptying it into the sink (see the section «REMOVING WA-

TER OUT OF THE APPLIANCE»). Fill your appliance with

10

fresh water to the MAX fill level and place an empty cup on the

drip tray.

10.Set the on/off switch to the on position and wait for the water

to be dispensed into the cup.

11.Discard the water in the cup.

12.Repeat steps 10 and 11 until the water level is at the MIN

mark. Open the lid and empty any remaining water into the

sink (see the section «DE-SCALING THE APPLIANCE»).

Any other works should be performed in the authorized ser-

vice center.

Do not store the appliance if it is hot or connected to the

network. If you do not use the appliance, put it in a box after

ENGLISH

cooling and store in a safe, dry place, out of children’s reach.

List of possible problems:

Problem

Possible cause

Solution

The power on/off

The appliance hasn’t

Wait a little and try

switch can not be

cooled down after

again

fixed in the operation

the last use

position

The appliance is not

Check the connec-

connected to the

tion of the appliance

No backlighting in

mains supply

to the mains supply

the water con-

The appliance is po-

Check the correct

tainer. The

sitioned incorrectly

positioning of the ap-

appliance doesn’t

on the base

pliance

heat water

Safety cut-off is burnt

Consult service facil-

ity

No water in the ap-

Let the appliance

pliance

cool down, then fill it

with water

The appliance boils

Excessive level of

De-scale the appli-

non-full cup of water

scale

ance

Large amount of

Water level is below

Maintain the proper

steam during the boil-

the minimum marking

water level inside the

ing process and the

water container (be-

absence of water in

tween the minimum

the cup

and maximum

marks)

Excessive level of

De-scale the appli-

scale

ance

During the boiling

The appliance boils

Wait for the boiling

process the power

the fixed amount of

cycle to finish and let

on/off switch was

water (250 ml). The

water pour into the

pressed, but the pro-

capacity is not ad-

tray for drops. Wait

cess of boiling hasn’t

justed manually.

for water to cool and

stopped

When the tempera-

pour it out of the tray

ture of water reaches

a certain point, wa-

ter is automatically

poured into the cup

The appliance makes

After the boiling pro-

This is normal

some noise; after boil-

cess is finished you

11