Fein WPO 14-15XE: en For your safety.

16

en For your safety.

Read all safety warnings and all instruc-

tions. 

Failure to follow the warnings 

and instructions may result in electric 

shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

Do not use this power tool before you have thor-

oughly read and completely understood this 

Instruction Manual and the enclosed “General 

Safety Instructions” (document number 

3 41 30 054 06 1). The documents mentioned should be 

kept for later use and enclosed with the power tool, 

should it be passed on or sold.

Please also observe the relevant national industrial safety 

regulations.

Intended use of the power tool:

hand-guided polisher for polishing in weather-protected 

environments using the application tools and accessories 

recommended by FEIN.

This machine is also intended to be powered by a.c. gen-

erators with sufficient power output that correspond 

with ISO 8528, design class G2. Compliance with this 

Standard in particular is not given when the so-called dis-

tortion factor exceeds 10%. When in doubt, inform 

yourself about the generator in use.

Safety warnings common for sanding, sanding with 

sanding sheets, working with wire brushes, 

polishing and cut-off grinding

This power tool is to be used as a polisher. Observe all 

safety warnings, instructions, illustrations and data sup-

plied with the power tool. 

Non-observance of the follow-

ing instructions can lead to electric shock, fire and/or 

serious injury.

Operations such as grinding or cutting-off are not recom-

mended to be performed with this power tool.

 Operations 

for which the power tool was not designed may create a 

hazard and cause personal injury.

Do not use accessories which are not specifically designed 

and recommended by the tool manufacturer.

 Just because 

the accessory can be attached to your power tool, it does 

not assure safe operation.

The rated speed of the accessory must be at least equal to 

the maximum speed marked on the power tool.

 Accessories 

running faster than their rated speed can break and fly 

apart.

The outside diameter and the thickness of your accessory 

must be within the capacity rating of your power tool.

Incorrectly sized accessories cannot be adequately 

guarded or controlled.

The arbor size of wheels, flanges, backing pads or any other 

accessory must properly fit the spindle of the power tool.

Accessories with arbor holes that do not match the 

mounting hardware of the power tool will run out of bal-

ance, vibrate excessively and may cause loss of control.

Do not use a damaged accessory. Before each use inspect 

the accessory such as abrasive wheels for chips and 

cracks, backing pad for cracks, tear or excess wear, wire 

brush for loose or cracked wires. If power tool or accessory 

is dropped, inspect for damage or install an undamaged 

accessory. After inspecting and installing an accessory, 

position yourself and bystanders away from the plane of the 

rotating accessory and run the power tool at maximum no-

load speed for one minute.

 Damaged accessories will nor-

mally break apart during this test time.

Wear personal protective equipment. Depending on appli-

cation, use face shield, safety goggles or safety glasses. As 

appropriate, wear dust mask, hearing protectors, gloves 

and workshop apron capable of stopping small abrasive or 

workpiece fragments.

 The eye protection must be capable 

of stopping flying debris generated by various operations. 

Character

Unit of measure, 

international

Unit of measure, 

national

Explanation

n

/min

rpm

Rated speed

V

V

Rated voltage

P

1

W

W

Power input

P

2

W

W

Output

f

Hz

Hz

Frequency

M…

mm

mm

Size of metric thread

L

wA

dB

dB

Sound power level

L

pA

dB

dB

Sound pressure level

L

pCpeak

dB

dB

Peak sound pressure level

K…

Uncertainty

m/s

2

m/s

2

Vibration emission value (triax vector sum) deter-

mined according to EN 60745

m/s

2

m/s

2

Mean vibrational value for polishing

m, s, kg, A, mm, V, 

W, Hz, N, °C, dB, 

min, m/s

2

m, s, kg, A, mm, V, 

W, Hz, N, °C, dB, 

min, m/s

2

Basic and derived units of measure from the inter-

national system of units 

SI

.

h,P

WARNING

3 41 01 118 06 0.book  Seite 16  Donnerstag, 10. Dezember 2009  7:39 07