Fein MBS32F: en For your safety.

17

en For your safety.

Read all safety warnings and all instruc-

tions provided with the magnetic drill 

stand or the power tool.

 Failure to fol-

low the warnings and instructions may result in electric 

shock, fire and/or serious injury.

Save all safety warnings and instructions for future refer-

ence.

Do not use this product before you have thor-

oughly read and completely understood this 

Instruction Manual and the enclosed “General 

Safety Instructions” (document number 

3 41 30 054 06 1

). The documents mentioned should 

be kept for later use and enclosed with the product, 

should it be passed on or sold.

Please also observe the relevant national industrial safety 

regulations.

Intended use of the magnetic drill stand:

Magnetic drill stand for holding a drive motor, for drilling 

with core drill bits and solid drill bits, reaming and tapping 

on materials with surfaces suitable for magnets in 

weather-protected environments using the application 

tools and accessories recommended by FEIN.

Special safety instructions.

Pull the plug from the mains receptacle and/or remove the 

battery before making adjustments on the tool or changing 

tool accessories.

 Unintentional switching on of the power 

tool is the cause of many accidents.

Before mounting the power tool, install the magnetic drill 

stand correctly. 

The correct installation is important in 

order to prevent the risk of the drill stand folding 

together.

Fasten the power tool securely to the magnetic drill stand 

before using it. 

Slipping off of the power tool on the mag-

netic drill stand can lead to loss of control.

Do not overload the magnetic drill stand. 

Overloading the 

magnetic drill stand can cause it to tip over.

Wear personal protective equipment. Depending on appli-

cation, use face shield, safety goggles or safety glasses. As 

appropriate, wear dust mask, hearing protectors, gloves 

and workshop apron capable of stopping small abrasive or 

workpiece fragments.

 The eye protection must be capable 

of stopping flying debris generated by various operations. 

The dust mask or respirator must be capable of filtrating 

particles generated by your operation. Prolonged expo-

sure to high intensity noise may cause hearing loss.

When there is danger of falling down, secure the magnetic 

drill stand using the provided lashing strap; especially 

when working aloft, on vertical building elements or over-

head. 

In case of a power failure or when the mains plug 

is pulled, the magnetic holding power is not maintained.

Prevent (cooling) liquids from penetrating into the mag-

netic drill stand, especially when working on walls and ceil-

ings. 

Penetrating liquids can lead to danger of an electric 

shock.

Operate the magnetic drill stand only from socket outlets 

with the earthing contact according to regulations. Only use 

undamaged supply cords and regularly checked extension 

cords with earthing contact. 

A protective conductor with-

out continuity can lead to electric shock.

Do not direct the power tool against yourself, other persons 

or animals.

 Danger of injury from sharp or hot application 

tools.

Do not rivet or screw any name-plates or signs to the mag-

netic drill stand. 

If the insulation is damaged, protection 

against an electric shock will be ineffective. Adhesive 

labels are recommended.

Do not use accessories not specifically intended and recom-

mended for the magnetic drill stand by the manufacturer. 

Just because the accessory can be attached to your mag-

netic drill stand, it does not assure safe operation.

Before putting into operation, check the mains connection 

and the mains plug for damage.

Recommendation: Always operate the power tool via a 

residual current device (RCD) with a rated residual current 

of 30 mA or less.

Operating instructions.

When a power tool is mounted that is 

not intended for use with the magnetic 

drill stand, the magnetic drill stand can 

tip over.

Use the magnetic drill stand suitable for the performance 

characteristics of your drive motor. 

Please make sure that the contacting surface for the mag-

netic foot is level, clean and rust-free. Remove any var-

nish or primer.

Use the magnetic drill stand only with the magnetic foot 

switched on.

When working on materials that are not magnetizable, 

suitable fixation devices, obtainable as accessories from 

FEIN, e. g. suction plate, vacuum plate or pipe-drilling 

device must be used.

Character

Unit of measure, 

international

Unit of measure, 

national

Explanation

mm

mm

Adjustment range

l x w

mm

mm

Magnetic foot plate dimensions

mm

mm

d

1

 = collar diameter of drive motor

m, s, kg, A, mm, V, 

W, Hz, N, °C, dB, 

min, m/s

2

m, s, kg, A, mm, V, 

W, Hz, N, °C, dB, 

min, m/s

2

Basic and derived units of measure from the inter-

national system of units 

SI

.

WARNING

WARNING

3 41 01 128 06 0.book  Seite 17  Dienstag, 15. März 2011  8:58 08