Brennenstuhl Solar Energy Set SES P4033 Solar celltype Mono-crystalline 2x20Wp Panel dimensions 592x 641x25mm Inverter 150W: Solar Energy Set SES P4033 V3

Solar Energy Set SES P4033 V3

GB

8

Frequently asked questions

Question:

 What type of batteries can be used with the kit?

Answer:

 Any 12 V/33 Ah battery that is used for cars, boats,

motor cycles, etc.

Question: 

Will the solar panels over-charge my battery?

Answer: 

The charge regulator ensures that a steady charge

is supplied to the battery and will not be over-charged.

Question: 

Can I extend/lengthen the battery lead?

Answer: 

If the lead is extended this can result in a loss of voltage 

and insuf

fi

 cient power transferred from the solar panels to charge 

the battery.

Question:

 How do I clean the solar panels?

Answer:

 Dust & dirt should 

fi

 rst be swept off the panel surface 

using a soft brush then using a wet cloth to wipe the panel surface 

to remove remaining dirt & grime. It is recommended that any bird 

droppings be removed as soon as possible as if left can cause 

damage to the surface.

Question: 

Is the solar panel kit water proof?

Answer:

 It is recommended that the kit is not exposed to exces-

sive water as all components apart from the solar panel are not 

water proof.

Maintenance

●

  Very little maintenance is required to keep the inverter and 

charge regulator operating properly. Clean the housing periodi-

cally with a damp cloth to prevent accumulation of dust and 

dirt.

●

  The surface of the solar panel should be kept clean by periodi-

cally wiping it with a soft cloth to ensure best performance.

●

  During long-term storage without being charged, the battery 

must be completely recharged every 4-6 months in order to 

preserve complete and proper performance.

Technical Data

SOLAR PANEL

Cell type:  

Mono-Crystalline

Output power Pmax:  

40 Wp (2x 20 Wp)

Upm:  

17.2 V

Dimension:  

(592 x 641 x 25) mm open

(296 x 641 x 50) mm folded

SOLAR CHARGE REGULATOR

Max. solar input current:  

10 A

Max. load current:  

10 A

Over-discharge protection:   11 ± 0.3 V

Over-charge protection:  

14.0 – 14.5 V

USB output socket  

5 V DC, 500 mA

Ambient humidity:  

≤

 80%

Operating temperature:  

-10°C up to +42°C

Fuse:  

10 A

POWER INVERTER

Output power (continuous):  150 W

Output power (peak):  

300 W

Stand-by current:  

≤

 0.3 A

Target input voltage (DC):  

12 V (11 V - 15 V)

Target output voltage (AC):   230 V AC, 50 Hz

Frequency:  

50 Hz

USB port:  

5 V DC, 500 mA

Output waveform:  

modi

fi

 ed sine wave

Safety

Low battery voltage alarm:   10.5 ± 0.5 V 

Low battery voltage cutout:   10.0 ± 0.5 V

Thermal protection:  

65 °C 

Overload:  

shutoff

Fuse:  

20 A

BATTERY (not included)

Recommended:  

12 V/33 Ah; seal lead acid, 

deep cycle, long life

(art. no. 1292990)

Note: Power & Current outputs are calculated at maximum and 

will vary depending on operating conditions, environments, battery 

condition, etc.

Disposal

Dispose of electronic devices in an eco-friendly fashion!   

  Electronic devices do not belong in your household waste.  

  Compliant with European Guideline 2002/96/EG for electric 

and electronic devices, used electronic devices must be collected 

separately and taken in for environmentally sound recycling. 

Options for disposing of used devices may be obtained from your 

township, city or municipal government.

 Incorrect disposal of batteries and rechargeable batteries    

          can harm the environment! Batteries and rechargeable 

          batteries do not belong in the household waste. They can 

contain poisonous heavy metals and are subject to treatment as 

hazardous wastes. Take your used batteries to a municipal collec-

tion site.

Manufacturer

Hugo Brennenstuhl GmbH & Co. KG

Seestraße 1-3 • 72074 Tübingen • Germany

H. Brennenstuhl S.A.S. • F-67460 Souffelweyersheim

lectra-t ag • Blegistrasse 13 • CH-6340 Baar

For further information please see the Service/FAQ section of our

website www.brennenstuhl.com