Delonghi KD-3S 60IX: ENGLISH

GB

ENGLISH

treated as domestic waste, but should be delivered to a

GENERAL

suitable electric and electronic appliance recycling

Carefully read the following important information

collection point. Follow local guidelines when disposing

regarding installation safety and maintenance. Keep this

of waste. For more information on the treatment, re-use

information booklet accessible for further consultations.

and recycling of this product, please contact your local

The appliance has been designed for use in the ducting

authority, domestic waste collection service or the shop

version (air exhaust to the outside), filtering version (air

where the appliance was purchased.

circulation on the inside ) or with external motor .

INSTALLATION INSTRUCTIONS

SAFETY PRECAUTION

Assembly and electrical connections must be carried

1. Take care when the cooker hood is operating

out by specialised personnel.

simultaneously with an open fireplace or burner that

depend on the air in the environment and are supplied

• Electric Connection

by other than electrical energy, as the cooker hood

The appliance has been manufactured as a class II,

removes the air from the environment which a burner or

therefore no earth cable is necessary.

fireplace need for combustion. The negative pressure in

The connection to the mains is carried out as follows:

-5

the environment must not exceed 4Pa (4x10

bar).

BROWN = L line

Provide adequate ventilation in the environment for a

BLUE = N neutral

safe operation of the cooker hood.

If not provided, connect a plug for the electrical load

Follow the local laws applicable for external air

indicated on the description label. Where a plug is

evacuation.

provided, the cooker hood must be installed in order that

the plug is easily accessible.

Before connecting the model to the electricity net-

An omnipolar switch with a minimum aperture of 3mm

work:

between contacts, in line with the electrical load and local

- control the data plate (positioned inside the appliance)

standards, must be placed between the appliance and

to ascertain that the voltage and power correspond to

the network in the case of direct connection to the

the network and the socket is suitable. If in doubt ask a

electrical network.

qualified electrician.

- If the power supply cable is damaged, it must be

• The minimum distance between the support surfaces

replaced with another cable or a special assembly, which

of the cooking pots on the cooker top and the lowest

may be obtained direct from the manufacturer or from

part of the cooker hood must be at least 65 cm.

the Technical Assistance Centre.

If a connection tube composed of two parts is used, the

upper part must be placed outside the lower part.

2. WARNING !

Do not connect the cooker hood exhaust to the same

In certain circumstances electrical appliances may

conductor used to circulate hot air or for evacuating fumes

be a danger hazard.

from other appliances generated by other than an

A) Do not check the status of the filters while the

electrical source.

cooker hood is operating

Before proceeding with the assembly operations, remove

B) Do not touch bulbs or adjacent areas, during or

the anti-grease filter(s) (Fig.5) so that the unit is easier

straight after prolonged use of the lighting

to handle.

installation.

C) Flambè cooking is prohibited underneath the

In the case of assembly of the appliance in the suction

cooker hood

version prepare the hole for evacuation of the air.

D) Avoid free flame, as it is damaging for the filters

and a fire hazard

• We recommend the use of an air exhaust tube which

E) Constantly check food frying to avoid that the

has the same diameter as the air exhaust outlet hole. If

overheated oil may become a fire hazard

a pipe with a smaller diameter is used, the efficiency of

F) Disconnect the electrical plug prior to any

the product may be reduced and its operation may

maintenance.

become noisier.

G) This appliance is not intended for use by young

children or infirm persons without supervision

• Warning! Plastic spacer fitting.

H) Young children should be supervised to ensure

This product may also be supplied with a plastic spacer O,

they do not play with the appliance

which should be fitted before the hood is installed (Fig. 2a).

I) There shall be adequate ventilation of the room

Fix the spacer to the hood using screws P (Fig. 2a).

when the rangehood is used at the same time as

To assemble the unit correctly, align the front panel of the

appliances burning gas or other fuels

hood with the wall cabinet and decide on the distance

L) There is a risk of fire if cleaning is not carried out

necessary to fill in any space remaining between the hood

in accordance with the instructions

and the wall.

Once the distance has been established, use a cutter to

This appliance conforms to the European Directive EC/

remove the excess plastic (Fig. 2a).

2002/96, Waste Electrical and Electronic Equipment

(WEEE). By making sure that this appliance is disposed

• INSTALLATION

of in a suitable manner, the user is helping to prevent

The following instruction should be followed to carry out

potential damage to the environment or to public health.

the correct installation of the cooker hood.

1) Mounting of the cooker hood on the lower side of

The

symbol on the product or on the accompanying

the cupboard.

paperwork indicates that the appliance should not be

2) Selection of the version (extraction or filtration)

- 18 -

• FIXING THE HOOD TO THE LOWER PART OF THE

denatured alcohol or non-abrasive neutral liquid

WALL CABINET

detergent.

This type of appliance must be fitted inside a cabinet or

• The light on the cooker hood is designed for use during

inside another type of support structure. To fix it in place,

cooking and not for general room illumination. Extended

use 4 screws which are suitable for the type of cabinet,

use of the light reduces the average duration of the bulb.

making holes in accordance with the diagram shown in

(fig. 1). To fit the appliance correctly, align the front panel

• Replacing halogen light bulbs (Fig. 8).

of the cooker hood with the cabinet door and adjust

To replace the halogen light bulbs B, remove the glass

spacer E using screws P (fig. 2), then ensure the

pane C using a lever action on the relevant cracks.

appliance meets the cabinet at the rear.

Replace the bulbs with new ones of the same type.

Caution: do not touch the light bulb with bare hands.

• EXTRACTION THROUGH AN OUTSIDE WALL

The appliance expels the fumes through an outside wall

MICROSWITCH (fig. 9).

or a duct. It is necessary to buy a telescopic pipe in

Warning! This hood is fitted with a

microswitch which

accordance with the standards in use (inflammable) and

allows the activation of the functions (light and motor

connect it to flange B (Fig 3).

speed) through the opening of the telescopic

undercarriage.

• RECIRCULATION

If the telescopic undercarriage is closed, neither the lights

To transform the cooker hood from the extraction version

nor the motor speed can be activated (fig. 9).

to the re circulating one ask your supplier for an activated

carbon filter.

•COMMANDS: (pic.9) SLIDER

the key symbols are ex-

The filter must be fitted to the extracting group cooker

plained below:

hood in the centre of the fan grille by twisting it by 90

A = Light switch

degrees until it is gripped securely (Fig 6). For this

A1 = Off key

operation remove the anti-grease filter(s) G (Fig 5). The

A2 = On key

clean air is returned into the room through a connecting

B = Speed control

tube passing inside the cupboard and connected to the

B1 = Off key

ring B (fig 4).

B2 = FIRST SPEED key

B3 = SECOND SPEED key

B4 = THIRD SPEED key

USE AND MAINTENANCE

• COMANDI: (Fig.7) SLIDER the key symbols are

• We recommend that the cooker hood is switched on

explained below:

before any food is cooked. We also recommend that the

This hood is fitted with a

microswitch which allows the

appliance is left running for 15 minutes after the food is

activation of the motor speed) through the opening of

cooked, in order to thoroughly eliminate all contaminated

the telescopic undercarriage. If the telescopic

air.

undercarriage is closed the motor speeds cannot be

The effective performance of the cooker hood depends

activated.

on constant maintenance; the anti-grease filter and the

This microswitch does not have an impact on the

active carbon filter both require special attention.

activation of the lights which must be switched on through

• The anti-grease filter is used to trap any grease particles

the appropriate switch (see fig.7A).

suspended in the air, therefore is subject to saturation

(the time it takes for the filter to become saturated

A = Light switch

depends on the way in which the appliance is used).

A1 = Off key

The acrylic filter, which is found resting on the grille,

A2 = On key

should be replaced when the text, visible through the

B = Speed control

grille, changes colour and the ink spreads; the new filter

B1 = FIRST SPEED key

should be fitted in such a way that the text can be seen

B2 = SECOND SPEED key

through the grille from outside the cooker hood.

B3 = THIRD SPEED ke

If the filters do not have any text on them, or if metal

filters or aluminium panel filters are used, they should

Warning! If the telescopic undercarriage is closed with

be washed every 2 months in order to prevent the risk of

the speed set at 2,, once it is re-opened, the hood will

fire. To wash the filters, proceed as follows:

be reactivated with the same speed in use when the hood

- Remove the filter from the grille and wash it using a

was closed.

solution of water and neutral liquid detergent, leaving

the dirt to soften.

THE MANUFACTURER DECLINES ALL

- Rinse thoroughly with warm water and leave to dry.

RESPONSIBILITY FOR EVENTUAL DAMAGES

The metal filters and/or aluminium panel are also

CAUSED BY BREACHING THE ABOVE WARNINGS.

dishwasher safe. If the filters are made using aluminium,

or if an aluminium panel is used, after a few washes the

colour may change. This does not mean they have to be

replaced.

If the replacement and washing instructions are not

followed, the anti-grease filters may present a fire hazard.

• The active carbon filters are used to purify the air which

is released back into the room. The filters are not

washable or re-usable and must be replaced at least once

every four months. The active carbon filter saturation level

depends on the frequency with which the appliance is

used, the type of cooking performed and the regularity

with which the anti-grease filters are cleaned.

• Remove build-up from the fan and other surfaces of

the cooker hood regularly using a cloth moistened with

- 19 -