Skil 9345 AG: 5)SERVICE SAFETY INSTRUCTIONS FOR ANGLE GRINDERS 1)SAFETYINSTRUCTIONSFORALLOPERATIONS 2)KICKBACKANDRELATEDWARNINGS
5)SERVICE SAFETY INSTRUCTIONS FOR ANGLE GRINDERS 1)SAFETYINSTRUCTIONSFORALLOPERATIONS 2)KICKBACKANDRELATEDWARNINGS: Skil 9345 AG
Table of contents
- INTRODUCTION 3)PERSONALSAFETY TECHNICAL DATA 1 TOOL ELEmENTS 2 SAFETY GENERAL SAFETY INSTRUCTIONS 1)WORKAREASAFETY 4)POWERTOOLUSEANDCARE 2)ELECTRICALSAFETY
- 5)SERVICE SAFETY INSTRUCTIONS FOR ANGLE GRINDERS 1)SAFETYINSTRUCTIONSFORALLOPERATIONS 2)KICKBACKANDRELATEDWARNINGS
- 3)SAFETYWARNINGSSPECIFICFORGRINDINGAND ABRASIVECUTTING-OFFOPERATIONS 5)SAFETYWARNINGSSPECIFICFORSANDING OPERATIONS 6)SAFETYWARNINGSSPECIFICFORWIRE BRUSHING OPERATIONS GENERAL ACCESSORIES 4)ADDITIONALSAFETYWARNINGSSPECIFICFOR CUTTING OFF OPERATIONS OUTDOOR USE BEFORE USE
- DURING USE AFTER USE USE
- APPLICATIONADVICE MAINTENANCE/SERVICE ENVIRONMENT DECLARATION OF CONFORmITY NOISE/VIBRATION

Power tools are dangerous in the hands of untrained
h) Wearpersonalprotectiveequipment 4. Depending
users.
onapplication,usefaceshield,safetygogglesor
e) Maintainpowertools.Checkformisalignmentor
safetyglasses.Asappropriate,weardustmask,
bindingofmovingparts,breakageofpartsandany
hearingprotectors,glovesandshopaproncapable
otherconditionthatmayaffectthepowertool’s
ofstoppingsmallabrasiveorworkpiecefragments.
operation.Ifdamaged,havethepowertoolrepaired
The eye protection must be capable of stopping ying
beforeuse. Many accidents are caused by poorly
debris generated by various operations. The dust mask or
maintained power tools.
respirator must be capable of ltrating particles
f) Keepcuttingtoolssharpandclean. Properly
generated by your operation. Prolonged exposure to high
maintained cutting tools with sharp cutting edges are less
intensity noise may cause hearing loss.
likely to bind and are easier to control.
i) Keepbystandersasafedistanceawayfromwork
g) Usethepowertool,accessoriesandtoolbitsetc.,in
area.Anyoneenteringtheworkareamustwear
accordancewiththeseinstructions,takinginto
personalprotectiveequipment.Fragments of the
accounttheworkingconditionsandtheworktobe
workpiece or of a broken accessory may y away and
performed. Use of the power tool for operations dierent
cause injury beyond the immediate area of operation.
from those intended could result in a hazardous situation.
j) Holdpowertoolbyinsulatedgrippingsurfacesonly,
5)SERVICE
whenperforminganoperationwherethecutting
a) Haveyourpowertoolservicedbyaqualifiedrepair
accessorymaycontacthiddenwiringoritsown
personusingonlyidenticalreplacementparts. This
cord. A cutting accessory contacting a “live” wire may
will ensure that the safety of the power tool is maintained.
make exposed metal parts of the power tool “live” and
could give the operator an electric shock.
SAFETY INSTRUCTIONS FOR ANGLE GRINDERS
k) Positionthecordclearofthespinningaccessory.If
you lose control, the cord may be cut or snagged and your
1)SAFETYINSTRUCTIONSFORALLOPERATIONS
hand or arm may be pulled into the spinning accessory.
a) Thispowertoolisintendedtofunctionasagrinder,
l) Neverlaythepowertooldownuntiltheaccessory
sander,wirebrushorcut-offtool.Readallsafety
hascometoacompletestop.The spinning accessory
warnings,instructions,illustrationsand
may grab the surface and pull the power tool out of your
specificationsprovidedwiththispowertool.Failure
control.
to follow all instructions listed below may result in electric
m) Donotrunthepowertoolwhilecarryingitatyour
shock, re and/or serious injury.
side.Accidental contact with the spinning accessory
b) Thispowertoolisnotrecommendedforpolishing.
could snag your clothing, pulling the accessory into your
Operations for which the power tool was not designed
body.
may create a hazard and cause personal injury.
n) Regularlycleanthepowertool’sairvents.The
c)
Donotuseaccessorieswhicharenotspecifically
motor’s fan will draw the dust inside the housing and
designedandrecommendedbythetoolmanufacturer.
excessive accumulation of powdered metal may cause
Just because the accessory can be attached to your power
electrical hazards.
tool, it does not assure safe operation.
o) Donotoperatethepowertoolnearflammable
d) Theratedspeedoftheaccessorymustbeatleast
materials.Sparks could ignite these materials.
equaltothemaximumspeedmarkedonthepower
p) Donotuseaccessoriesthatrequireliquidcoolants.
tool.Accessories running faster than their rated speed
Using water or other liquid coolants may result in
can y apart.
electrocution or shock.
e) Theoutsidediameterandthethicknessofyour
2)KICKBACKANDRELATEDWARNINGS
accessorymustbewithinthecapacityratingofyour
• Kickback is a sudden reaction to a pinched or snagged
powertool.Incorrectly sized accessories cannot be
rotating wheel, backing pad, brush or any other
adequately guarded or controlled.
accessory. Pinching or snagging causes rapid stalling of
f) Threadedmountingofaccessoriesmustmatchthe
the rotating accessory which in turn causes the
grinderspindlethread.Foraccessoriesmountedby
uncontrolled power tool to be forced in the direction
flanges,thearbourholeoftheaccessorymustfit
opposite of the accessory’s rotation at the point of the
thelocatingdiameteroftheflange. Accessories that
binding.
do not match the mounting hardware of the power tool
• For example, if an abrasive wheel is snagged or pinched
will run out of balance, vibrate excessively and may
by the workpiece, the edge of the wheel that is entering
cause loss of control.
into the pinch point can dig into the surface of the
g) Donotuseadamagedaccessory.Beforeeachuse
material causing the wheel to climb out or kick out. The
i
nspecttheaccessorysuchasabrasivewheelsfor
wheel may either jump toward or away from the operator,
chipsandcracks,backingpadsforcracks,tearor
depending on the direction of the wheel’s movement at
excesswear,wirebrushesforlooseorcrackedwires.
the point of pinching. Abrasive wheels may also break
Ifthepowertooloraccessoryisdropped,inspectfor
under these conditions.
damageorinstallanundamagedaccessory.After
• Kickback is the result of power tool misuse and/or
inspectingandinstallinganaccessory,position
incorrect operating procedures or conditions and can be
yourselfandbystandersawayfromtheplaneofthe
avoided by taking proper precautions as given below.
rotatingaccessoryandrunthepowertoolat
a)
Maintainafirmgriponthepowertoolandposition
maximumnoloadspeedforoneminute.Damaged
yourbodyandarmtoallowyoutoresistkickback
accessories will normally break apart during this test time.
7

