Bork CH BRE 1818 SI – страница 2
Инструкция к Электрообогревателю Bork CH BRE 1818 SI
Instruction manual
Eng
This heater is not intended for use in wet or damp locations. Never
locate a heater where it may fall into a bathtub or other water
container.
Do not use this heater in the immediate surroundings of a bath,
a shower or a swimming pool.
Do not use heater outdoors.
In order to avoid overheating, do not cover the heater.
The heater must not be located immediately below a socket-
outlet.
This heater includes an audible alarm to warn that parts of the
heater are getting excessively hot. If the alarm sounds, immediately
turn the heater off and inspect for any objects on or adjacent to
the heater that may cause high temperature. DO NOT OPERATE
THE HEATER WITH THE ALARM SOUNDING.
SAFETY FEATURES
1. This heater includes an audible alarm to warn that parts of the
heater are getting excessively hot. If the alarm sounds, immediately
turn the heater off and inspect for any objects on or adjacent to
the heater that may cause high temperature. DO NOT OPERATE
THE HEATER WITH THE ALARM SOUNDING.
2. A thermal overload protector is built in to prevent overheating.
3. When an overheat temperature is reached, the heater will be
automatically shut off. It can only resume operation when the user
resets the unit. (See RESET INSTRUCTION below)
21
Oscillating ceramic heater with thermostat CH BRE 1818 SI
RESET INSTRUCTION
1. Unplug the heater and wait 10 minutes for the unit to cool
down.
2. After the 10 minutes, plug the unit in again and operate
normally.
TROUBLE SHOOTING TIPS
If your heater shuts off unexpectedly or fails to operate, one of the
above-mentioned safety features may have activated to prevent
overheating.
1. Be sure the power cord is plugged into a working electrical
outlet.
2. Check your thermostat setting. The heater may be off because it
has reached the desired temperature setting.
MAINTENANCE
WARNING: ALWAYS UNPLUG THE CORD BEFORE MOVING OR
SERVICING. DO NOT IMMERSE HEATER IN WATER!
22
Instruction manual
Eng
CLEANING
IMPORTANT! DO NOT IMMERSE HEATER IN WATER! Clean the heater
grills with the vacuum brush attachment on your vacuum cleaner.
This will remove lint and dirt from the inside of the heater. DO NOT
ATTEMPT TO TAKE HEATER APART. Clean the body of heater with a
soft cloth.
CAUTION: Do not use gasoline, benzine, thinner, harsh cleaners,
etc. as they will damage the heater. NEVER USE ALCOHOL OR
SOLVENTS.
STORAGE
Store the heater with these instructions in the original carton in a
cool, dry place.
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling advice.
23
Oscillating ceramic heater with thermostat CH BRE 1818 SI
>
COMPLETE SET
Ceramic heater 1
Remote control 1
Instruction manual 1
Warranty card 1
>
DESCRIPTION
1. Top control panel
2. Display panel
3. Handle
4. Warm outlet opening
5. Metal mesh
6. Body
7. Remote controller bracket
8. Base withtip-over switch
9. Warm outletopening
10. Air inlet opening (dust filter inside)
11. Remote controller
12. Power switch
13. Plug
24
Instruction manual
Eng
Description
25
1
2
3
9
4
10
5
6
7
11
8
12
13
Oscillating ceramic heater with thermostat CH BRE 1818 SI
>
OPERATION GUIDE
26
2
1
3
Figure 1
Figure 2
1
3
2
4
Instruction manual
Eng
Figure 2
1. Mode & set time button
2. Power & thermostat Knob
3. Oscillation button
Figure 3
1. Mode indicator
2. Power indicator
3. Set time indicator
4. LED display
The heater may be operated by the manual controls located on
the heater (as shown in Figure 2) or by the remote controller. The
heater working state may be known from display panel (as shown
in Figure 3).
1. Carefully remove the heater from the bag and the carton.
2. The heater must be placed on a firm, level surface.
3. Plug the cord set into a 220-240V� electrical outlet. Be sure plug
fits tightly in outlet. A loose fit will cause overheating and damage
the plug. Plug and cord set may feel warm during normal usage.
4. When the heater is initially plugged in and turn on the power switch
on the base, there will be a “beep” and the red light will come on
indicating that there is power to the unit. The red light will remain
lit until the power switch on the base is turned off.
27
Oscillating ceramic heater with thermostat CH BRE 1818 SI
5. Turn the heater on by pressing the Power & Thermostat knob.
6. The LED displayer on the display panel will display the current
room temperature.
7. Upon turning the heater on, the unit will be in the HIGH heat mode
(1800 watts) and the HIGH indicator will be light.
8. Pressing the Mode & set time button at this point will set the heater
into the LOW heat mode (1100 watts).
9. Pressing the Mode & set time button once more will set the heater
into the AUTO mode. Notice that the display now displays a set
temperature indicator.(see THERMOSTAT INSTRUCTION)
10. To turn the heater off, press the Power & Thermostat knob and
turn off power switch, then remove plug from power outlet..
Oscillation Function
This function will work in any mode. Pressing the oscillation button
(OSC.) will allow the heater to oscillate back and forth. To stop the
oscillation, press the oscillation button once more.
Timer Function
This function will work in any mode. The timer function allows you to
set the length of operation from 0.5 hour to 7.5 hours.
Keep to press the Mode & set time button for above two seconds,
“0.5” indicator flickering indicates to enter the Timer Function.
Rotating the Power & Thermostat knob clockwise will increase the
28
Instruction manual
Eng
length of operation by 0.5 hour. Rotating the Power & Thermostat
knob counter-clockwise will decrease the length of operation by 0.5
hour.
When all timer indicator light, continuing to rotate the Power &
Thermostat knob clockwise, the indicator will no change. When only
“0.5” indicator lights, continuing to rotate the Power & Thermostat
knob counter-clockwise, all indicator will be off and the heater will
run continuously.
Once the timer has been set, the timer will count down the hours
in 0.5 hour increments, and the indicator will display the remaining
operating time, until the heater will turn itself off.
THERMOSTAT INSTRUCTION
1. Press the Mode & set time button until the Mode indicator lights
in AUTO mode.
2. To adjust set temperature, Rotate the Power & Thermostat knob
clockwise to increase the desired temperature and counter-
clockwise to decrease the desired temperature.
3. When the air temperature reaches 2 degrees above the set
temperature, the heater will stop to heat at once and stop to blow
after 15 seconds.
4. When the air temperature drops 1 degree below the set
temperature, the unit will come back on.
29
Oscillating ceramic heater with thermostat CH BRE 1818 SI
Remote control
NOTE: It is normal for the heater to cycle ON and OFF as it maintains
the set temperature.
NOTE: When adjusting set temperature, the set temperature on
display will flicker for 5 seconds and the heater will stop oscillating. In
5 seconds, if not to rotate the Power & Thermostat knob, LED will stop
to flicker and display room temperature and restart to oscillate.
REMOTE CONTROL
1. Plug the heater into outlet and open the power switch on the
base.
2. Press the POWER button will start the heater.
3. The OSC., SET TIME and MODE buttons function in the exact same
manner as listed in the OPERATION instructions above.
4. The TEMP. buttons (+,-) are for the thermostat function in the exact
same as the Power & Thermostat knob.
5. The remote control is powered by two AAA batteries. There is a
cover on the back of the remote control that can be removed for
replacement of the batteries as required.
6. Do not mix old and new batteries, or batteries of different
specifications.
30
Instruction manual
Eng
31
Товар сертифицирован в соответствии
с законом «О защите прав потребителей»
- 1
- 2
