Yamaha RX-797: Setting remote control codes
Setting remote control codes: Yamaha RX-797
Table of contents
- CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
- CONTENTS
- FEATURES SUPPLIED ACCESSORIES
- CONTROLS AND FUNCTIONS Front panel
- CONTROLS AND FUNCTIONS
- Front panel display
- CONTROLS AND FUNCTIONS Rear panel
- CONTROLS AND FUNCTIONS Remote control
- CONTROLS AND FUNCTIONS
- Zone 2 remote control
- Installing batteries in the remote controls Using the remote controls
- CONNECTIONS Connecting speakers
- Connecting audio and video components
- Connecting the AM and FM antennas
- ■ Connecting the AM loop antenna
- Connecting the power supply cord
- Turning on and off this unit
- PLAYING AND RECORDING Playing a source
- PLAYING AND RECORDING
- Adjusting the tonal quality
- Recording a source
- Using the sleep timer
- Muting the sound output
- FM/AM TUNING Automatic tuning
- Manual tuning
- Automatic preset tuning
- FM/AM TUNING
- FM/AM TUNING Manual preset tuning
- FM/AM TUNING Selecting preset stations Exchanging preset stations
- RADIO DATA SYSTEM (EUROPE MODEL ONLY) Receiving Radio Data System Changing the Radio Data System stations mode
- PTY SEEK function
- EON function
- ADVANCED SETUP Changing the ADVANCED SETUP menu parameters
- Switching the remote control ID
- ZONE 2 Connecting the Zone 2 components
- Controlling Zone 2
- REMOTE CONTROL FEATURES Control area
- Controlling other components
- Setting remote control codes
- TROUBLESHOOTING ■ General
- ■ Tuner
- ■ Remote control
- SPECIFICATIONS
- LIST OF REMOTE CONTROL CODES
REMOTE CONTROL FEATURES
Setting remote control codes
1 Press and hold CODE SET on the remote
control and then press one of the input
You can control other components by setting the
selector buttons on the remote control to
appropriate remote control codes. Codes can be set up for
select the input source you want to set up.
each input source. For a complete list of available remote
control codes, refer to “LIST OF REMOTE CONTROL
CODES” at the end of this manual.
CODE SET
POWER POWER
STANDBY
POWER
MENU
AVTV
The following table show the default component category
CD
MD/TAPE
TUNER
DTV/CBL
VCR
PHONODVD
(library) and the remote control code for each input
source.
Note
Remote control code default settings
You must press and hold CODE SET throughout this
Default
operation.
Default
Input
component
Manufacturer
YAMAHA
source
category
code
2 While holding down CODE SET on the
(library)
remote control, use the numeric buttons on
CD CD YAMAHA 199
the remote control to enter the three-digit
remote control code for the selected input
MD/TAPE TAPE YAMAHA 499
source.
DVD DVD YAMAHA 699
When the setting succeeds, “PRESET OK” appears;
DTV/CBL*
———
however, when it does not, “PRESET NG” appears in
the front panel display.
VCR ———
To reset the code, enter the default code for each
PHONO ———
input source listed in the remote control code default
settings table.
———
4321
*
65
7
8
You can only set the TV remote control codes for the DTV/
09
10
ENT.
CBL button. However, other remote control codes can be set
CODE SET
MENUTITLE
BAND
for any input selector buttons except DTV/CBL.
MENU
ENTER
A/B/C/D/E A/B/C/D/E
DISPLAYRETURN
PRESET/CH
Note
You may not be able to operate your other YAMAHA
components even if the YAMAHA remote control code is
initially set as listed above. In this case, try setting other
Notes
YAMAHA remote control codes.
• If the manufacturer of your component has more than one
code, try setting each of them until you find the correct
one.
• You can only assign one remote control code to each input
selector button.
38
