Yamaha RX-797: CONTROLS AND FUNCTIONS Remote control
CONTROLS AND FUNCTIONS Remote control: Yamaha RX-797
Table of contents
- CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
- CONTENTS
- FEATURES SUPPLIED ACCESSORIES
- CONTROLS AND FUNCTIONS Front panel
- CONTROLS AND FUNCTIONS
- Front panel display
- CONTROLS AND FUNCTIONS Rear panel
- CONTROLS AND FUNCTIONS Remote control
- CONTROLS AND FUNCTIONS
- Zone 2 remote control
- Installing batteries in the remote controls Using the remote controls
- CONNECTIONS Connecting speakers
- Connecting audio and video components
- Connecting the AM and FM antennas
- ■ Connecting the AM loop antenna
- Connecting the power supply cord
- Turning on and off this unit
- PLAYING AND RECORDING Playing a source
- PLAYING AND RECORDING
- Adjusting the tonal quality
- Recording a source
- Using the sleep timer
- Muting the sound output
- FM/AM TUNING Automatic tuning
- Manual tuning
- Automatic preset tuning
- FM/AM TUNING
- FM/AM TUNING Manual preset tuning
- FM/AM TUNING Selecting preset stations Exchanging preset stations
- RADIO DATA SYSTEM (EUROPE MODEL ONLY) Receiving Radio Data System Changing the Radio Data System stations mode
- PTY SEEK function
- EON function
- ADVANCED SETUP Changing the ADVANCED SETUP menu parameters
- Switching the remote control ID
- ZONE 2 Connecting the Zone 2 components
- Controlling Zone 2
- REMOTE CONTROL FEATURES Control area
- Controlling other components
- Setting remote control codes
- TROUBLESHOOTING ■ General
- ■ Tuner
- ■ Remote control
- SPECIFICATIONS
- LIST OF REMOTE CONTROL CODES
CONTROLS AND FUNCTIONS
Remote control
This section describes the function of each button on the
3 Radio Data System control buttons
INTRODUCTION
remote control used to control this unit or other
Controls the Radio Data System features.
components made by YAMAHA or other manufacturers.
The functions of the buttons used to control your other
Note
audio and video components are the same as those of the
The Radio Data System features (FREQ/TEXT, EON, PTY
corresponding buttons on those components. Refer to
SEEK MODE and PTY SEEK START) are only applicable to the
those components’ instruction manuals for details. To
Europe model and are operational only when TUNER is selected
operate other components using this remote control, see
as the input source. For details, see “Receiving Radio Data
“REMOTE CONTROL FEATURES” on page 36.
System stations” on page 29.
1
4 Numeric buttons (1 to 8)
Select the preset station number (1 to 8) when TUNER is
7
POWER POWER
STANDBY
POWER
selected as the input source.
AVTV
8
5 BAND
CD
MD/TAPE
TUNER
Switches to the previously used reception band (FM or
9
AM) when TUNER is selected as the input source.
2
DTV/CBL
VCR
PHONODVD
Note
REC
CODE SET
SPEAKERS
A
DISC SKIP
0
The frequency of the previously received station is automatically
B
recalled.
FREQ/TEXT
EON
SLEEP
A
3
B
6 A/B/C/D/E j / i
MODE PTY SEEK
START
Selects the preset station group (A to E) when TUNER
TV VOL
TV CH
VOLUME
C
is selected as the input source (see page 28).
TV MUTE TV INPUT
PRESET/CH u / d
MUTE
D
Selects the preset station number (1 to 8) when
4321
TUNER is selected as the input source (see page 28).
4
65
7
8
7 STANDBY
09
10
ENT.
Sets this unit to the standby mode.
5
MENUTITLE
Notes
BAND
6
ENTER
• This button is operational only when MASTER ON/OFF on the
A/B/C/D/E A/B/C/D/E
front panel is pressed inward to the ON position.
DISPLAYRETURN
• In the standby mode, this unit consumes a small amount of
PRESET/CH
power to receive infrared signals from the remote control.
• This button does not set Zone 2 to the standby mode.
8 POWER
Turns on this unit.
(Europe model)
Notes
1 Infrared signal transmitter
• This button is operational only when MASTER ON/OFF on the
front panel is pressed inward to the ON position.
Sends infrared signals.
• This button does not turn on Zone 2.
2 Input selector buttons
Select the desired input source and change the control area
(see page 36).
English
7
