Skil 1764 AK: APPLICATION ADVICE MAINTENANCE / SERVICE ENVIRONMENT DECLARATION OF CONFORMITY

- turn switch E to the desired operating mode until it

APPLICATION ADVICE

snap-locks

• Use the appropriate bits ^

! start working only when switch E is locked

! only use sharp bits/chisels

1 = normal drilling/screwdriving

• When drilling ferrous metals

2 = impact drilling

- pre-drill a smaller hole, when a large hole is required

3 = chiseling with rotating chisel

- lubricate drill bit occasionally with oil

4 = chiseling with xed chisel

• When turning in a screw at/near the cross cut end or an

! select operating mode only when tool is switched

edge of wood, pre-drill a hole in order to avoid cracking of

off and plug is disconnected

the wood

- the hammer mechanism is activated by applying a

• Splinterfree drilling in wood &

slight pressure on the tool when the drill bit is in

• Dustfree drilling in walls *

contact with the workpiece

• Dustfree drilling in ceilings (

- best hammer drilling results can be obtained by only a

• Drilling in tiles without skidding )

slight pressure on the tool needed to keep the

• For more tips see www.skil.com

automatic clutch engaged; drilling performance will not

improve by applying more pressure on the tool

• Chiseling with rotating chisel 0

MAINTENANCE / SERVICE

! switch off the tool and disconnect the plug

• This tool is not intended for professional use

- select “rotating” chiseling mode

• Always keep tool and cord clean (especially ventilation

• Chiseling with xed chisel !

slots K 2)

! switch off the tool and disconnect the plug

! disconnect the plug before cleaning

- select “rotating” chiseling mode

• If the tool should fail despite the care taken in

- place chisel in desired position

manufacturing and testing procedures, repair should be

- select “xed” chiseling mode

carried out by an after-sales service centre for SKIL

• Changing bits @

power tools

! clean and lightly lubricate the SDS+ accessory

- send the tool undismantled together with proof of

before insertion

purchase to your dealer or the nearest SKIL service

- pull back locking sleeve G and insert accessory in

station (addresses as well as the service diagram of

SDS+ chuck while turning and pushing it until it

the tool are listed on www.skil.com)

engages; the accessory locks in position automatically

- pull accessory to check that it is locked correctly

ENVIRONMENT

- remove accessory by pulling back locking sleeve G

! the SDS+ accessory requires freedom of

• Do not dispose of electric tools, accessories and

movement which causes eccentricity when tool is

packaging together with household waste material

off-load; however, the accessory automatically

(only for EU countries)

centres itself during operation without affecting

- in observance of European Directive 2002/96/EC on

drilling precision

waste of electric and electronic equipment and its

! do not use bits/chisels with a damaged shank

implementation in accordance with national law,

For drilling in wood, metal and plastic as well as for

electric tools that have reached the end of their life

screwdriving use adapter H #

must be collected separately and returned to an

- clean and lightly lubricate adapter before insertion

environmentally compatible recycling facility

- pull back locking sleeve G and insert adapter in SDS+

- symbol ¡ will remind you of this when the need for

chuck while turning and pushing it until it engages; the

disposing occurs

adapter locks in position automatically

- pull adapter to check whether is it locked correctly

DECLARATION OF CONFORMITY

- set switch E 2 to normal drilling (only activate when

• We declare under our sole responsibility that the product

tool is switched off and plug is disconnected)

described under “Technical data” is in conformity with the

• Safety clutch

following standards or standardization documents: EN

If the accessory gets jammed, the drive to the spindle is

60745, EN 61000, EN 55014, in accordance with the

interrupted (causing a rattling noise)

provisions of the directives 2004/108/EC, 2006/42/EC,

- immediately switch o tool

2011/65/EU

- remove the jammed accessory

• Technical file at: SKIL Europe BV (PT-SEU/ENG1),

- switch on tool again

4825 BD Breda, NL

• Adjusting drilling depth $

• Holding and guiding the tool %

! while working, always hold the tool at the

grey-coloured grip area(s)

- always use auxiliary handle J (can be adjusted as

illustrated)

- keep the ventilation slots uncovered

- do not apply too much pressure on the tool; let the tool

do the work for you

11

12.08.2013