Skil 1735 AA: MAINTENANCE / SERVICE ENVIRONMENT DECLARATION OF CONFORMITY APPLICATION ADVICE NOISE/VIBRATION

- it takes a short time for the hammer mechanism to

MAINTENANCE / SERVICE

reach full impact power

• This tool is not intended for professional use

- best hammer drilling results can be obtained by only a

• Always keep tool and cord clean (especially the

slight pressure on the tool needed to keep the

ventilation slots)

automatic clutch engaged; drilling performance will not

! disconnect the plug before cleaning

improve by applying more pressure on the tool

• If the tool should fail despite the care taken in

• Changing bits 0

manufacturing and testing procedures, repair should be

! clean and lightly lubricate the SDS+ accessory

carried out by an after-sales service centre for SKIL

before insertion

power tools

- pull back locking sleeve F 2 and insert accessory in

- send the tool undismantled together with proof of

SDS+ chuck while turning and pushing it until it

purchase to your dealer or the nearest SKIL service

engages; the accessory locks in position automatically

station (addresses as well as the service diagram of

- pull accessory to check that it is locked correctly

the tool are listed on www.skil.com)

- remove accessory by pulling back locking sleeve F

! the SDS+ accessory requires freedom of

movement which causes eccentricity when tool is

ENVIRONMENT

off-load; however, the accessory automatically

• Do not dispose of electric tools, accessories and

centres itself during operation without affecting

packaging together with household waste material

drilling precision

(only for EU countries)

! do not use bits with a damaged shank

- in observance of European Directive 2002/96/EC on

• Safety clutch

waste of electric and electronic equipment and its

If the accessory gets jammed, the drive to the spindle is

implementation in accordance with national law,

interrupted (causing a rattling noise)

electric tools that have reached the end of their life

- immediately switch o tool

must be collected separately and returned to an

- remove the jammed accessory

environmentally compatible recycling facility

- switch on tool again

- symbol ( will remind you of this when the need for

• Adjusting drilling depth !

disposing occurs

• Holding and guiding the tool @

! while working, always hold the tool at the

DECLARATION OF CONFORMITY

grey-coloured grip area(s)

- always use auxiliary handle G 2 (can be adjusted

• We declare under our sole responsibility that the product

as illustrated)

described under “Technical data” is in conformity with the

- keep the ventilation slots uncovered

following standards or standardization documents: EN

- do not apply too much pressure on the tool; let the tool

60745, EN 61000, EN 55014, in accordance with the

do the work for you

provisions of the directives 2004/108/EC, 2006/42/EC,

2011/65/EU

• Technical file at: SKIL Europe BV (PT-SEU/ENG1),

APPLICATION ADVICE

4825 BD Breda, NL

• Use the appropriate bits #

! only use sharp bits

• For drilling in wood, metal and plastic as well as for

screwdriving use the corresponding adapter (SKIL

accessory 2610395660) $

- clean and lightly lubricate adapter before insertion

- pull back locking sleeve F 2 and insert adapter in

SDS+ chuck while turning and pushing it until it

engages; the adapter locks in position automatically

- pull adapter to check whether is it locked correctly

- set switch E 2 to normal drilling (only activate when

tool is switched off and plug is disconnected)

• When drilling ferrous metals

- pre-drill a smaller hole, when a large hole is required

- lubricate drill bit occasionally with oil

• When turning in a screw at/near the cross cut end or an

edge of wood, pre-drill a hole in order to avoid cracking of

the wood

• Splinterfree drilling in wood %

• Dustfree drilling in walls ^

• Dustfree drilling in ceilings &

• Drilling in tiles without skidding *

• For more tips see www.skil.com

8

12.08.2013

NOISE/VIBRATION

• Measured in accordance with EN 60745 the sound

pressure level of this tool is 91 dB(A) and the sound

power level 102 dB(A) (standard deviation: 3 dB), and the

vibration ✱ (hand-arm method; uncertainty K = 1.5 m/s²)

✱ when hammer drilling in concrete 15.5 m/s²

• The vibration emission level has been measured in

accordance with a standardised test given in EN 60745; it

may be used to compare one tool with another and as a

preliminary assessment of exposure to vibration when

using the tool for the applications mentioned

- using the tool for dierent applications, or with dierent

or poorly maintained accessories, may signicantly

increase the exposure level