Skil 0760 RA: MAINTENANCE/SERVICE ENVIRONMENT DECLARATION OF CONFORMITY TROUBLESHOOTING NOISE/VIBRATION

MAINTENANCE/SERVICE

ENVIRONMENT

• This tool is not intended for professional use

• Donotdisposeofelectrictools,accessoriesand

• Beforemaintenancealwaysswitchofftool,ensure

packagingtogetherwithhouseholdwastematerial

thereisnowaterpressureintoolandhandgun,

(only for EU countries)

disconnectplugfrompowersource,anddisconnect

- in observance of European Directive 2002/96/EC on

toolfromwatersupply

waste of electric and electronic equipment and its

• Always keep tool and cord clean (especially ventilation

implementation in accordance with national law,

slots S 2)

electric tools that have reached the end of their life

- do not use water, solvents or polishes

must be collected separately and returned to an

- regularly clean spraying nozzle G using cleaning

environmentally compatible recycling facility

needle M 0 (remove spray lance K from hand gun L

- symbol @ will remind you of this when the need for

rst)

disposing occurs

• Regularly check for worn or damaged components and

have them repaired/replaced when necessary

DECLARATION OF CONFORMITY

• Cleaning water lter

• We declare under our sole responsibility that the product

- remove water lter E 2 from inlet connector C 2 with

described under “Technical data” is in conformity with the

long nose pliers

following standards or standardization documents: EN

- rinse it clean and put it back (replace it when

60335, EN 61000, EN 55014 in accordance with the

damaged)

provisions of the directives 2006/95/EC, 2004/108/EC,

! neverusethetoolwithadamagedwaterfilter

2006/42/EC, 2000/14/EC, 2011/65/EU

• Storage !

• Technicalfileat: SKIL Europe BV (PT-SEU/ENG1),

- store the tool out of reach of children in a location

4825 BD Breda, NL

where the ambient temperature will not exceed 40°C

or drop below 0°C

- do not place other objects on top of the tool

- securely mount storage rail N on the wall with 4 screws

(notsupplied) and horizontally leveled

- use storage rail N and storage straps P as illustrated

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of

the tool are listed on www.skil.com)

TROUBLESHOOTING

• The following listing shows problem symptoms, possible

causes and corrective actions (if these do not identify

and correct the problem, contact your dealer or service

station)

! switchoffthetoolanddisconnecttheplugbefore

investigatingtheproblem

★ Spray is not consistent

- nozzle partly blocked -> clean nozzle

★ Motor does not start or stops suddenly

- power supply socket faulty -> use another socket

- plug not connected -> connect plug

- thermal protection switched o the motor -> let the tool

cool down for 5 minutes

★ Motor is running but spray is poor

- nozzle completely blocked -> clean nozzle

- water lter clogged -> clean water lter

- air in the pump -> ensure that water inlet connector is

securely tted

- inadequate water supply -> check that water tap is

fully open

8

30.07.2013

10

NOISE/VIBRATION

• Measured in accordance with EN 60704-1 the sound

pressure level of this tool is 81dB(A) and the sound

power level 93 dB(A) (standard deviation: 3 dB), and the

vibration 2.5 m/s² (hand-arm method; uncertainty

K = 1.5 m/s²)

• Measured in accordance with 2000/14/EC the

guaranteed sound power level LWA is lower than 97

dB(A) (conformity assessment procedure according to

Annex V)

• The vibration emission level has been measured in

accordance with a standardised test given in EN/ISO

5349; it may be used to compare one tool with another

and as a preliminary assessment of exposure to vibration

when using the tool for the applications mentioned

- using the tool for dierent applications, or with dierent

or poorly maintained accessories, may signicantly

increase the exposure level

- the times when the tool is switched o or when it is

running but not actually doing the job, may signicantly

reduce the exposure level

! protectyourselfagainsttheeffectsofvibration

bymaintainingthetoolanditsaccessories,

keepingyourhandswarm,andorganizingyour

workpatterns