Skil 0730 RA: MAINTENANCE / SERVICE ENVIRONMENT DECLARATION OF CONFORMITY TROUBLESHOOTING NOISE/VIBRATION

- after replacing the spool system test-run the tool for at

- trimmer incorrectly used -> only trim with the tip of the

least one minute without load to ensure that the tool is

line; avoid stones, walls and other hard objects; feed

operating properly

the line regularly

MAINTENANCE / SERVICE

ENVIRONMENT

• This tool is not intended for professional use

• Donotdisposeofelectrictools,accessoriesand

• Alwaysdisconnectplugfrompowersourcebefore

packagingtogetherwithhouseholdwastematerial

cleaningand/ormaintenance

(only for EU countries)

• Always keep tool and cord clean (especially the

- in observance of European Directive 2002/96/EC on

ventilation slots)

waste of electric and electronic equipment and its

- clean the tool with a damp cloth (do not use cleaning

implementation in accordance with national law,

agents or solvents)

electric tools that have reached the end of their life

- clean line cutting blade J 2 and cutting guard A 2

must be collected separately and returned to an

after each use

environmentally compatible recycling facility

- clean ventilation slots L 2 regularly with a brush or

- symbol 9 will remind you of this when the need for

compressed air

disposing occurs

• Regularly check the condition of the cutting head and the

tightness of nuts, bolts and screws

DECLARATION OF CONFORMITY

• Regularly check for worn or damaged components and

• We declare under our sole responsibility that the product

have them repaired/replaced when necessary

described under “Technical data” is in conformity with the

• Storage (

following standards or standardization documents: EN

- store the tool indoors in a dry and locked-up place,

60335, EN 61000, EN 55014 in accordance with the

out of reach of children

provisions of the directives 2006/95/EC, 2004/108/EC,

- securely mount storage rail M on the wall with 4

2006/42/EC, 2000/14/EC, 2011/65/EU

screws (notsupplied) and horizontally leveled

• Technicalfileat: SKIL Europe BV (PT-SEU/ENG1),

• If the tool should fail despite the care taken in

4825 BD Breda, NL

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of

the tool are listed on www.skil.com)

TROUBLESHOOTING

• The following listing shows problem symptoms, possible

causes and corrective actions (if these do not identify

and correct the problem, contact your dealer or service

station)

! switchoffthetoolanddisconnecttheplugbefore

investigatingtheproblem

★ Tool does not operate

- power supply socket faulty -> use another socket

- extension cord damaged -> replace extension cord

★ Tool operates intermittently

- internal wiring defective -> contact dealer/service

station

- on/o switch defective -> contact dealer/service

station

★ Tool vibrates abnormally

- grass too high -> cut in stages

★ Tool does not cut

- line too short/broken o -> feed the line manually

★ Line cannot be fed

- spool empty -> replace spool

- line entangled inside spool -> inspect spool; rewind if

necessary

★ Line is not cut o to correct length -> remove cover from

cutting blade

★ Line keeps breaking

- line entangled inside spool -> inspect spool; rewind if

necessary

8

30.07.2013

10

NOISE/VIBRATION

• Measured in accordance with EN 60335 the sound

pressure level of this tool is 70 dB(A) and the sound

power level 90 dB(A) (standard deviation: 3 dB), and the

vibration <2.5 m/s² (hand-arm method; uncertainty K =

1.5 m/s²)

• Measured in accordance with 2000/14/EC (EN/ISO

3744) the guaranteed sound power level LWA is lower

than 93 dB(A) (conformity assessment procedure

according to Annex VI)

Notied body : KEMA, Arnhem, NL

Notied body identication number : 0344

• The vibration emission level has been measured in

accordance with a standardised test given in EN 60335; it

may be used to compare one tool with another and as a

preliminary assessment of exposure to vibration when

using the tool for the applications mentioned

- using the tool for dierent applications, or with dierent

or poorly maintained accessories, may signicantly

increase the exposure level

- the times when the tool is switched o or when it is

running but not actually doing the job, may signicantly

reduce the exposure level