Skil 0715 RT: ELECTRICAL SAFETY ) 5) SERVICE EXPLANATION OF SYMBOLS ON TOOL BEFORE USE GENERAL DURING USE
ELECTRICAL SAFETY ) 5) SERVICE EXPLANATION OF SYMBOLS ON TOOL BEFORE USE GENERAL DURING USE: Skil 0715 RT
Table of contents
- INTRODUCTION 3) PERSONAL SAFETY TECHNICAL DATA ① TOOL ELEMENTS ③ SAFETY 1) WORK AREA SAFETY 4) POWER TOOL USE AND CARE 2) ELECTRICAL SAFETY
- ELECTRICAL SAFETY ) 5) SERVICE EXPLANATION OF SYMBOLS ON TOOL BEFORE USE GENERAL DURING USE
- USE TROUBLESHOOTING
- ENVIRONMENT DECLARATION OF CONFORMITY
c)
- before checking, cleaning or working on the tool
- after striking a foreign object
- whenever the tool starts vibrating abnormally
Such preventive safety measures reduce
ELECTRICAL SAFETY
the risk of starting the power tool accidentally.
Inspect the cord periodically and have it replaced by a
d)
qualied person, if damaged
When operating the tool use a residual current device
(RCD) with a triggering current of 30 mA maximum
Use completely unrolled and safe extension cords with a
Power tools are dangerous in the hands of untrained
capacity of 16 Amps (U.K. 13 Amps)
users.
Only use an extension cord of types H05VV-F or
e)
H05RN-F which is intended for outdoor use and
equipped with a watertight plug and coupling-socket
Do not run over, crush or pull the (extension) cord
Protect the (extension) cord from heat, oil and sharp
Many accidents are caused by poorly
edges
maintained power tools.
Inspect the extension cord periodically and replace it,
f) Properly
if damaged (
maintained cutting tools with sharp cutting edges are
)
less likely to bind and are easier to control.
PERSONAL SAFETY
g)
Do not operate the tool when barefoot or wearing open
sandals; always wear sturdy shoes and long trousers
Be familiar with the controls and the proper use of the
Use of the power tool for operations
tool
dierent from those intended could result in a hazardous
Never mow in the direct vicinity of persons (especially
situation.
children) and animals
5) SERVICE
a)
This will ensure that the safety of the power tool is
Switch on the motor according to instructions and with
feet well away from the cutting blade
maintained.
SPECIFIC SAFETY INSTRUCTIONS FOR LAWN
MOWERS
EXPLANATION OF SYMBOLS ON TOOL
(local
④ Read the instruction manual before use
regulations can restrict the age of the operator)
⑤ Double insulation (no earth wire required)
Ensure that children do not play with the tool
⑥
Operate the mower at a walking pace only (do not run)
(keep bystanders a safe distance away from
Keep proper footing on slopes and do not mow
work area)
extremely steep slopes
⑦ Beware of sharp blades
Be extremely careful when moving backwards or pulling
⑧ Keep the (extension) cord away from the rotating cutting
the mower towards you
blade
BEFORE USE
⑨ The cutting blade continues to rotate for a short time
Check the functioning of the tool before each use and,
after tool is switched o ()
in case of a defect, have it repaired immediately by a
⑩ Switch o and disconnect plug before cleaning/
qualied person; never open the tool yourself
maintenance or if (extension) cord is damaged or
Thoroughly inspect the area where the mower is to be
entangled
used and remove all hard objects which could be caught
⑪ Do not dispose of the tool together with household
up and thrown by the cutting mechanism
waste material
Always ensure that the cutting mechanism is in good
working order (have worn or damaged parts replaced)
Keep all nuts, bolts and screws tight to be sure that the
GENERAL
mower is in safe working condition
Avoid operating the mower on wet lawns
DURING USE
The user is responsible for accidents or hazards
Only mow with sucient daylight or with appropriate
occurring to other people or their property
articial lighting
Never operate the tool with a defective rear guard or
Do not tilt the tool when starting or switching on the
defective grass box
motor, except if the tool has to be tilted for starting
When operating the tool without grass box, ensure
in long grass (in this case, do not tilt it more than
that the rear guard is in closed position (
absolutely necessary and tilt only the part which is away
)
from the operator); always ensure that both hands are
Always disconnect plug from power source
in the operating position before returning the tool to the
- whenever leaving the tool unattended
ground
- before clearing jammed material
8
