Skil 1766 AK: ENVIRONMENT DECLARATION OF CONFORMITY APPLICATION ADVICE MAINTENANCE / SERVICE NOISE/VIBRATION

- it takes a short time for the hammer mechanism to

• Always keep tool and cord clean (especially ventilation

reach full impact power

slots H 2)

- do not apply too much pressure on the tool; let the tool

! disconnect the plug before cleaning

do the work for you

• If the tool should fail despite the care taken in

• Changing bits 7

manufacturing and testing procedures, repair should be

! clean and lightly lubricate the SDS+ accessory

carried out by an after-sales service centre for SKIL

before insertion

power tools

- pull back locking sleeve F 2 and insert accessory in

- send the tool undismantled together with proof of

SDS+ chuck while turning and pushing it until it

purchase to your dealer or the nearest SKIL service

engages; the accessory locks in position automatically

station (addresses as well as the service diagram of

- pull accessory to check that it is locked correctly

the tool are listed on www.skil.com)

- remove accessory by pulling back locking sleeve F

! the SDS+ accessory requires freedom of

ENVIRONMENT

movement which causes eccentricity when tool is

• Do not dispose of electric tools, accessories and

off-load; however, the accessory automatically

packaging together with household waste material

centres itself during operation without affecting

(only for EU countries)

drilling precision

- in observance of European Directive 2002/96/EC on

! do not use bits/chisels with a damaged shank

waste of electric and electronic equipment and its

• Safety clutch

implementation in accordance with national law,

If the accessory gets jammed, the drive to the spindle is

electric tools that have reached the end of their life

interrupted

must be collected separately and returned to an

- immediately switch o tool

environmentally compatible recycling facility

- remove the jammed accessory

- symbol & will remind you of this when the need for

- switch on tool again

disposing occurs

• Adjusting drilling depth 8

• Holding and guiding the tool 9

! while working, always hold the tool at the

DECLARATION OF CONFORMITY

grey-coloured grip area(s)

• We declare under our sole responsibility that this product

- always use auxiliary handle G 2 (can be adjusted

is in conformity with the following standards or

as illustrated)

standardized documents: EN 60745, EN 61000, EN

- keep ventilation slots H 2 uncovered

55014, in accordance with the provisions of the directives

2004/108/EC, 2006/42/EC, 2011/65/EU

APPLICATION ADVICE

• Technical file at: SKIL Europe BV (PT-SEU/ENG1),

4825 BD Breda, NL

• Use the appropriate bits 0

! only use sharp bits/chisels

• For drilling in wood, metal and plastic as well as for

screwdriving use the corresponding adapter (SKIL

accessory 2610395660) !

- clean and lightly lubricate adapter before insertion

- pull back locking sleeve F 2 and insert adapter in

SDS+ chuck while turning and pushing it until it

engages; the adapter locks in position automatically

- pull adapter to check whether is it locked correctly

- set switch D 2 to normal drilling (only activate when

tool is switched off and plug is disconnected)

• When drilling ferrous metals

- pre-drill a smaller hole, when a large hole is required

- lubricate drill bit occasionally with oil

• When turning in a screw at/near the cross cut end or an

edge of wood, pre-drill a hole in order to avoid cracking of

the wood

• Splinterfree drilling in wood @

• Dustfree drilling in walls #

• Dustfree drilling in ceilings $

• Drilling in tiles without skidding %

• For more tips see www.skil.com

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Never open the tool yourself ^

9

25.09.2013

NOISE/VIBRATION

• Measured in accordance with EN 60745 the sound

pressure level of this tool is 95 dB(A) and the sound

power level 106 dB(A) (standard deviation: 3 dB), and the

vibration ✱ (hand-arm method; uncertainty K = 1.5 m/s²)

✱ when hammer drilling in concrete 17.0 m/s²

✱ when chiseling 16.0 m/s²

• The vibration emission level has been measured in

accordance with a standardised test given in EN 60745; it

may be used to compare one tool with another and as a

preliminary assessment of exposure to vibration when

using the tool for the applications mentioned

- using the tool for dierent applications, or with dierent

or poorly maintained accessories, may signicantly

increase the exposure level

- the times when the tool is switched o or when it is

running but not actually doing the job, may signicantly

reduce the exposure level