Gigabyte GA-8IE800: Chapter 2 Hardware Installation Process

Chapter 2 Hardware Installation Process: Gigabyte GA-8IE800

Chapter 2 Hardware Installation Process

To set up your computer, you must complete the following steps:

English

Step 1- Install the Central Processing Unit (CPU)

Step 2- Install memory modules

Step 3- Install expansion cards

Step 4- Connect ribbon cables, cabinet wires, and power supply

Step 5- Setup BIOS software

Step 6- Install supporting software tools

Step4

Step1

Step 2

Step 4

Step 4

Step 4

Step3

- 8 -GA-8IE800 Motherboard

English

Step 1: Install the Central Processing Unit (CPU)

Step 1-1: CPU Installation

Angling the

Socket

0

rod to 65

Actuation

Lever

1. Angling the rod to 65-degree maybe feel

2. Pull the rod to the 90-degree

a kind of tight , and then continue pull

directly.

the rod to 90-degree when a noise cough

made.

Pin1 indicator

Pin1 indicator

4. Locate Pin 1 in the socket and look

3. CPU Top View

for a (golden) cut edge on the CPU

upper corner. Then insert the CPU

into the socket.

M Please make sure the CPU type is supported by the motherboard.

M If you do not match the CPU socket Pin 1 and CPU cut edge well, it will cause

improper installation. Please change the insert orientation.

- 9 - Hardware Installation Process

Step 1-2 : CPU Heat Sink Installation

English

2. Make sure the CPU fan is plugged to

1. Fasten the heatsink supporting-base

the CPU fan connector, than install

onto the CPU socket on the

complete.

mainboard.

M Please use Intel approved cooling fan.

M We recommend you to apply the thermal tape to provide better heat conduction between

your CPU and heatsink.

(The CPU cooling fan might stick to the CPU due to the hardening of the thermal paste.

During this condition if you try to remove the cooling fan, you might pull the processor out

of the CPU socket alone with the cooling fan, and might damage the processor. To avoid

this from happening, we suggest you to either use thermal tape instead of thermal paste, or

remove the cooling fan with extreme caution.)

M Make sure the CPU fan power cable is plugged in to the CPU fan connector, this completes

the installation.

M Please refer to CPU heat sink users manual for more detail installation procedure.

- 10 -GA-8IE800 Motherboard

English

Step 2: Install memory modules

The motherboard has 3 dual inline memory module (DIMM) sockets, but it can only support a

maximum of 4 banks of DDR memory. DDR sockets 1 uses 2 banks, DDR sockets 2&3 share the

remaining 2 banks. Please refer to the following tables for possible memory configurations supported.

The BIOS will automatically detects memory type and size. To install the memory module, just push

it vertically into the DIMM socket .The DIMM module can only fit in one direction due to the notch.

Memory size can vary between sockets.

Support Unbuffered DDR DIMM Sizes type:

64 Mbit (2Mx8x4 banks) 64 Mbit (1Mx16x4 banks) 128 Mbit(4Mx8x4 banks)

128 Mbit(2Mx16x4 banks) 256 Mbit(8Mx8x4 banks) 256 Mbit(4Mx16x4 banks)

512 Mbit(16Mx8x4 banks) 512 Mbit(8Mx16x4 banks)

Total System Memory (Max2GB)

Install memory in any combination table:

DDR1 DDR2 DDR3

S S S

D S S

D D X

D X D

S D X

S X D

DDR

D:Double Sided DIMM S:Single Sided DIMM

X:Not Use

1. The DIMM socket has a notch, so the

DIMM memory module can only fit in one direction.

2. Insert the DIMM memory module vertically into the

DIMM socket. Then push it down.

3. Close the plastic clip at both edges of the DIMM

sockets to lock the DIMM module.

Reverse the installation steps when you wish to

remove the DIMM module.

M When DIMM LED is ON, do not install/remove DIMM from socket.

M Please note that the DIMM module can only fit in one direction due to

the one notches. Wrong orientation will cause improper installation.

Please change the insert orientation.

- 11 - Hardware Installation Process

Step 3: Install expansion cards

1. Read the related expansion cards instruction document before install the expansion card into

the computer.

English

2. Remove your computers chassis cover, necessary screws and slot bracket from the computer.

3. Press the expansion card firmly into expansion slot in motherboard.

4. Be sure the metal contacts on the card are indeed seated in the slot.

5. Replace the screw to secure the slot bracket of the expansion card.

6. Replace your computers chassis cover.

7. Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS.

8. Install related driver from the operating system.

Please carefully pull out the small white-

drawable bar at the end of the AGP slot

when you try to install/ Uninstall the AGP

card. Please align the AGP card to the

onboard AGP slot and press firmly down on

AGP Card

the slot .Make sure your AGP card is locked

by the small white- drawable bar.

When an AGP 2x (3.3V) card is installed the 2X_DET will light up, indicating a non-supported

graphics card is inserted. Informing users that system might not boot up normally due to AGP 2x

(3.3V) is not supported by the chipset.

DDR Introduction

Established on the existing SDRAM industry infrastructure, DDR (Double Data Rate) memory is a

high performance and cost-effective solution that allows easy adoption for memory vendors, OEMs

and system integrators.

DDR memory is a sensible evolutionary solution for the PC industry that builds on the existing

SDRAM infrastructure, yet makes awesome advances in solving the system performance bottle-

neck by doubling the memory bandwidth. DDR SDRAM will offer a superior solution and migration

path from existing SDRAM designs due to its availability, pricing and overall market support. PC2100

DDR memory (DDR266) doubles the data rate through reading and writing at both the rising and

falling edge of the clock, achieving data bandwidth 2X greater than PC133 when running with the

same DRAM clock frequency. With peak bandwidth of 2.664GB per second, DDR memory enables

system OEMs to build high performance and low latency DRAM subsystems that are suitable for

servers, workstations, high-end PC's and value desktop SMA systems. With a core voltage of only

2.5 Volts compared to conventional SDRAM's 3.3 volts, DDR memory is a compelling solution for

small form factor desktops and notebook applications.

- 12 -GA-8IE800 Motherboard

English

Step 4: Connect ribbon cables, cabinet wires, and power

supply

Step 4-1 : I/O Back Panel Introduction

w

u

x

v

y

u PS/2 Keyboard and PS/2 Mouse Connector

PS/2 Mouse Connector

ØThis connector supports standard PS/2

(6 pin Female)

keyboard and PS/2 mouse.

PS/2 Keyboard Connector

(6 pin Female)

v USB Connector

Ø Before you connect your device(s) into USB

connector(s), please make sure your device(s)

such as USB keyboard, mouse, scanner, zip,

USB 1

speaker..etc. Have a standard USB interface.

USB 0

Also make sure your OS supports USB

controller. If your OS does not support USB

controller, please contact OS vendor for

possible patch or driver upgrade. For more

information please contact your OS or device(s)

vendors.

- 13 - Hardware Installation Process

w Parallel Port ,VGA port and Serial Ports (COMA)

Ø This connector supports 2 standard COM ports

Parallel Port

and 1 Parallel port. Device like printer can be

(25 pin Female)

English

connected to Parallel port ; mouse and modem

etc can be connected to Serial ports.

COMA

COMB

Serial Ports (9 pin Male)

x Game /MIDI Ports

Ø This connector supports joystick, MIDI keyboard

and other relate audio devices.

Joystick/ MIDI (15 pin Female)

Ø After install onboard audio driver, you may

y Audio Connectors

connect speaker to Line Out jack, micro phone

to MIC In jack.

Device like CD-ROM , walkman etc can be

connected to Line-In jack.

Please note:

Line Out

MIC In

You are able to use 2-/4-/6- channel audio

(Center and Subwoofer)

(Front

feature by S/W selection.

Speaker)

If you want to enable 6-channel function, you

Line In

have 2 choose for hardware connection.

(Rear Speaker)

Method1:

Connect Front Speaker to Line Out

Connect Rear Speaker to Line In

Connect Center and Subwooferr to MIC Out .

Method2:

You can refer to page 21, and contact your

nearest dealer for optional SUR_CEN cable.

If you want the detail information for 2-/4-/6-channel audio setup installation, please

refer to 2-/4-/6-Channel Audio Function Introduction”

- 14 -GA-8IE800 Motherboard

English

Step 4-2 :Connectors & Jumper Setting Introduction

1 3

4

15

5

13

18

12

17

2

7

16

6

9

14

11

10

8

1) CPU_FAN

10) F_USB1/F_USB2

2) SYS_FAN

11) SPDIF_IO

3) ATX_12V

12) SUR_CEN

4) ATX Power

13) CD_IN

5) FDD

14) AUX_IN

6) IDE1/IDE2

15) F_AUDIO

7) 2X_DET

16) CI

8) PWR_LED

17) CLR_PWD

9) F_PANEL

18) BAT

- 15 - Hardware Installation Process

1) CPU_FAN (CPU FAN Connector)

Please note, a proper installation of the CPU cooler is essential to prevent the CPU from running

under abnormal condition or damaged by overheating.The CPU fan connector supports Max.

current up to 600 mA.

English

Pin No. Definition

1 GND

1

2 +12V

3 Sense

2) SYS_FAN (System FAN Connector)

This connector allows you to link with the cooling fan on the system case to lower the system

temperature.

Pin No. Definition

1 GND

1

2 +12V

3 Sense

- 16 -GA-8IE800 Motherboard

English

3) ATX_12V ( +12V Power Connector)

This connector (ATX _12V) suppliesthe CPU operation voltage (Vcore). If this " ATX_ 12V

connector" is not connected, system cannot boot.

3

4

Pin No. Definition

1

2

1 GND

2 GND

3 +12V

4 +12V

4) ATX_POWER (ATX Power)

AC power cord should only be connected to your power supply unit after ATX power cable and

other related devices are firmly connected to the mainboard.

Pin No. Definition

1 3.3V

10

20

2 3.3V

3 GND

4 VCC

5 GND

6 VCC

7 GND

8 Power Good

9 5V SB(stand by +5V)

10 +12V

11 3.3V

12 -12V

13 GND

1 11

14 PS_ON(softOn/Off)

15 GND

16 GND

17 GND

18 -5V

19 VCC

20 VCC

- 17 - Hardware Installation Process

5) IDE1/ IDE2(IDE1/IDE2 Connector)

Please connect first harddisk to IDE1 and connect CDROM to IDE2. The red stripe of the ribbon

cable must be the same side with the Pin1.

English

2

40

IDE2

IDE1

1

39

6) FDD (Floppy Connector)

Please connect the floppy drive ribbon cables to FDD. It supports 360K,720K,1.2M,1.44M and

2.88Mbytes floppy disk types. The red stripe of the ribbon cable must be the same side with the

Pin1.

34

33

2

1

- 18 -GA-8IE800 Motherboard

English

7)2X_DET

When an AGP 2X (3.3V) card is installed the 2X_DET will light up, indicating a

nonsupported graphics card is inserted. Informing users that system might not boot

up normally due to AGP 2X (3.3V) is not supported by the chipset.

+

-

8) PWR_LED

PWR_LED is connect with the system power indicator to indicate whether the system is on/off. It

will blink when the system enters suspend mode. If you use dual color LED, power LED will turn

to another color.

Pin No. Definition

1 MPD+

2 MPD-

1

3 MPD-

- 19 - Hardware Installation Process

9) F_PANEL (2x10 pins connector)

Please connect the power LED, PC peaker, reset switch and power switch etc of your

chassis front panel to the F_PANEL connector according to the pin assignment above.

Soft Power

English

Connector

Speaker

Message LED/Power/

Connector

Sleep LED

PW-

MPD-

PW+

SPK+

SPK-

MPD+

1

1

1

202

1

1

1

19

IDE Hard Disk

HD+

HD-

NC

Active LED

RSE-

RSE+

Reset Switch

HD (IDE Hard Disk Active LED) Pin 1: LED anode(+)

(Blue) Pin 2: LED cathode(-)

SPK (Speaker Connector) Pin 1: VCC(+)

(Amber) Pin 2- Pin 3: NC

Pin 4: Data(-)

RES (Reset Switch) Open: Normal Operation

(Green) Close: Reset Hardware System

PW (Soft Power Connector) Open: Normal Operation

(Red) Close: Pow er On/Off

MSG(Message LED/Power/ Pin 1: LED anode(+)

Sleep LED)(Yellow) Pin 2: LED cathode(-)

NC( Purple) NC

10)F_ USB1 / F_USB2(Front USB Connector, Yellow )

Be careful with the polarity of the front USB connector. Check the pin assignment while you

connect the front USB cable. Please contact your nearest dealer for optional front USB cable.

Pin No. Definition

1 Power

2 Power

2

10

3 USB DX-

4 USB Dy-

5 USB DX+

6 USB Dy+

1

9

7 GND

8 GND

9 No Pin

10 NC

- 20 -GA-8IE800 Motherboard

English

11) SPDIF_IO (SPDIF In/Out)

The SPDIF output is capable of providing digital audio to external speakers or compressed AC3

data to an external Dolby Digital Decoder. Use this feature only when your stereo system has

digital input function.

Use SPDIF IN feature only when your device has digital output function.

Pin No. Definition

1 VCC

2 No Pin

3 SPDIF

2

6

4 SPDIFI

5 GND

6 GND

1

5

12) SUR_CEN

Please contact your nearest dealer for optional SUR_CEN cable.

Pin No. Definition

2

6

1 SUR OUTL

2 SUR OUTR

3 GND

1

5

4 No Pin

5 CENTER_OUT

6 BASS_OUT

- 21 - Hardware Installation Process

13) CD_IN (CD IN,Blank)

Connect CD-ROM or DVD-ROM audio out to the connector.

English

Pin No. Definition

1

1 CD-L

2 GND

3 GND

4 CD_R

14) AUX_IN ( AUX In Connector)

Connect other device(such as PCI TV Tunner audio out)to the connector.

Pin No. Definition

1 AUX-L

2 GND

1

3 GND

4 AUX_R

- 22 -GA-8IE800 Motherboard

English

15) F_AUDIO (F_AUDIO Connector)

If you want to use Front Audio connector, you must remove 5-6, 9-10 Jumper. In order to utilize the

front audio header, your chassis must have front audio connector. Also please make sure the pin

assigment on the cable is the same as the pin assigment on the MB header. To find out if the chassis

you are buying support front audio connector, please contact your dealer.

Pin No. Definition

1 MIC

2 GND

3 REF

1

2

4 POWER

5 FrontAudio(R)

10

9

6 RearAudio(R)

7 Reserved

8 No Pin

9 FrontAudio (L)

10 RearAudio(L)

16) CI (CASE OPEN)

This 2 pin connector allows your system to enable or disable the case open item in BIOS

if the system case begin remove.

Pin No. Definition

1 Signal

1

2 GND

- 23 - Hardware Installation Process

17) CLR_PWD

When Jumper is set to "open" and system is restarted, the password that is set will be cleared.

On the contrary when Jumper is set to "close", the current status remains

M PS, the function offers a solution for users who forget the password.

English

1

open: Clear password

1

close: Normal

18) BATTERY (Battery)

+

CAUTION

v Danger of explosion if battery is incorrectly

replaced.

v Replace only with the same or equivalent

type recommended by the manufacturer.

v Dispose of used batteries according to the

manufacturers instructions.

If you want to erase CMOS...

1.Turn OFF the computer and unplug the power cord.

2.Remove the battery, wait for 30 second.

3.Re-install the battery.

4.Plug the power cord and turn ON the computer.

- 24 -GA-8IE800 Motherboard