Skil 7220 (F0157220..): MAINTENANCE / SERVICE ENVIRONMENT DECLARATION OF CONFORMITY APPLICATION ADVICE NOISE/VIBRATION

- select position 1 for accurate sanding (when working

 Use dierent grit sizes when the working surface is

with delta-tip G or special sanding attachments H, J

rough:

or K)

- start sanding with coarse or medium grit

- select position 2 for fast sanding

- nish with ne grit

! 

 For more tips see www.skil.com

workpiece, you should switch on the tool

! 

MAINTENANCE / SERVICE

from the workpiece

 This tool is not intended for professional use

 Mounting special sanding attachments (not standard

 Always keep tool and cord clean (especially ventilation

included) ⑦

slots Q ②)

- mount base plate C (similar to mounting backing pads)

- remove adhering sanding dust with a brush

- mount attachment H, J or K onto base plate C and

! 

fasten it by turning knob L clockwise

 If the tool should fail despite the care taken in

- mount corresponding VELCRO sanding sheet to

manufacturing and testing procedures, repair should

sanding attachment

be carried out by an after-sales service centre for SKIL

- remove attachments or change their position by

power tools

turning knob L counter-clockwise

- send the tool undismantled together with proof of

- 5 sanding positions

purchase to your dealer or the nearest SKIL service

 Dust suction ⑧

station (addresses as well as the service diagram of

- empty dustbox M regularly for optimal dust pick-up

the tool are listed on www.skil.com)

performance

For using vacuum cleaner

ENVIRONMENT

- remove dustbox M by pressing knob N and hold it in

 Do not dispose of electric tools, accessories and

that position while pulling dustbox backwards

packaging together with household waste material

- connect vacuum cleaner to extension P

(only for EU countries)

! 

- in observance of European Directive 2002/96/EC

sanding metal

on waste of electric and electronic equipment and

 Holding and guiding the tool ⑨

its implementation in accordance with national law,

- guide the tool parallel to the working surface

electric tools that have reached the end of their life

! 

must be collected separately and returned to an

the sanding surface do the work for you

environmentally compatible recycling facility

- do not tilt the tool in order to avoid unwanted sanding

- symbol ⑮ will remind you of this when the need for

marks

disposing occurs

! 

coloured grip area(s)

- keep ventilation slots Q ② uncovered

DECLARATION OF CONFORMITY

 We declare under our sole responsibility that this

APPLICATION ADVICE

product is in conformity with the following standards

or standardized documents: EN 60745, EN 61000,

 Use the tool with the delta-tip pointing forward for

EN 55014, in accordance with the provisions of the

edged, narrow and other hard-to-reach places ⑩

directives 2004/108/EC, 2006/42/EC, 2011/65/EU

 Use the tool with the at side pointing forward for long

 : SKIL Europe BV (PT-SEU/ENG1),

strokes on at surfaces ⑪

4825 BD Breda, NL

 For sanding curved workpieces as well as for sanding

with high removal performance use the tool in

combination with backing pad A ②

 Use the tool with the special sanding attachments for

hard-to-reach places ⑫

 The exible sanding attachment is intended for

- rounding edged surfaces ⑬a

- all rounded surfaces with a maximum diameter of 10

cm ⑬b

 When the delta-tip G is worn or damaged at the top, you

may extend its service life twice by removing it, turning

it 120° and putting it back (also applicable to delta

sanding sheet) ⑭

 Never use the same sanding sheet for wood and metal

 Recommended sanding sheet grits:

coarse - for removing paint; for sanding of

extremely rough wood

medium - for sanding of rough or plain wood

ne - for smoothing of wood; for nishing

of bare wood; for smoothing

surfaces with old paint

8

NOISE/VIBRATION

 Measured in accordance with EN 60745 the sound

pressure level of this tool is 75 dB(A) and the sound

power level 86 dB(A) (standard deviation: 3 dB), and the

vibration 10.7 m/s² (hand-arm method; uncertainty K =

1.5 m/s²)

 The vibration emission level has been measured in

accordance with a standardised test given in EN 60745;

it may be used to compare one tool with another and as

a preliminary assessment of exposure to vibration when

using the tool for the applications mentioned