Skil 5265 AA: MAINTENANCE / SERVICE ENVIRONMENT APPLICATION ADVICE DECLARATION OF CONFORMITY

• Dust suction

as a guide, and use the right side of the foot against

- connect vacuum cleaner to extension P 7

this guide

! never let the vacuum cleaner hose interfere with

• For more tips see www.skil.com

the lower guard or the cutting operation

- one may also use a dust bag (SKIL accessory

MAINTENANCE / SERVICE

2610387402)

• This tool is not intended for professional use

• Operating the tool 7

• Always keep tool and cord clean (especially the

- connect plug to power source

ventilation slots)

- always hold handle Q rmly with one hand and handle

• Always keep the area around lower guard E 3 clean

R rmly with the other hand

(remove dust and chips by blowing out with compressed

- place tool with front end of foot at on workpiece

air or with a brush)

! ensure that the saw teeth are not engaged into

! disconnect the plug before cleaning

the workpiece

• Clean saw blade immediately after use (especially from

- switch on tool by rst pressing knob S (= safety switch

resin and glue)

which cannot be locked) and then pulling trigger T

• If the tool should fail despite the care taken in

! the tool should run at full speed before the blade

manufacturing and testing procedures, repair should be

enters into the workpiece

carried out by an after-sales service centre for SKIL

- lower guard E opens automatically when saw blade

power tools

enters the workpiece (open lower guard manually by

- send the tool undismantled together with proof of

using lever F only for special cuts such as plunge cuts)

purchase to your dealer or the nearest SKIL service

- do not force the tool; apply light and continuous pressure

station (addresses as well as the service diagram of

! while working, always hold the tool at the

the tool are listed on www.skil.com)

grey-coloured grip area(s)

- after completing the cut switch o tool by releasing

trigger T

ENVIRONMENT

! ensure that the blade has come to a complete

• Do not dispose of electric tools, accessories and

standstill, before you lift the tool from the

packaging together with household waste material

workpiece

(only for EU countries)

- in observance of European Directive 2002/96/EC on

APPLICATION ADVICE

waste of electric and electronic equipment and its

implementation in accordance with national law,

• Always face the good side of the workpiece down to

electric tools that have reached the end of their life

ensure minimum splintering

must be collected separately and returned to an

• Only use sharp saw blades of the correct type 8

environmentally compatible recycling facility

- quality of cut improves by the number of teeth

- symbol @ will remind you of this when the need for

- carbide tipped blades stay sharp up to 30 times longer

disposing occurs

than ordinary blades

• Parallel guide V 9

- for making exact cuts along a workpiece edge

DECLARATION OF CONFORMITY

- can be inserted in either side of foot

• We declare under our sole responsibility that the product

Adjusting parallel guide

described under “Technical data” is in conformity with the

- loosen knob W

following standards or standardization documents: EN

- adjust to desired cutting width by using parallel guide

60745, EN 61000, EN 55014, in accordance with the

scale (use line-of-cut indicator N as 0-reference)

provisions of the directives 2004/108/EC, 2006/42/EC,

- tighten knob W

2011/65/EU

• Plunge cutting 0

• Technical file at: SKIL Europe BV (PT-SEU/ENG1),

- set desired cutting depth

4825 BD Breda, NL

- tilt tool forward with line-of-cut indicator N lined up with

desired line of cut marked on the workpiece

- open lower guard E with lever F

- just before blade enters workpiece, switch on tool and

gradually lower back end of tool using front end of foot

as hinge-point

- gradually move tool downward as well as forward

- as soon as blade enters the material, release lever F

! never pull tool backwards

• Cutting large panels !

- support panel close to the cut either on oor, table or

workbench

! set cutting depth so that you cut through panel

and not through support

- in case parallel guide does not allow desired width of

cut, clamp or nail straight piece of wood to workpiece

11

12.08.2013

NOISE/VIBRATION

• Measured in accordance with EN 60745 the sound

pressure level of this tool is 99 dB(A) and the sound

power level 110 dB(A) (standard deviation: 3 dB), and the

vibration 2.7 m/s² (hand-arm method; uncertainty K = 1.5

m/s²)