Skil 0755 RA: MAINTENANCE / SERVICE ENVIRONMENT DECLARATION OF CONFORMITY TROUBLESHOOTING NOISE/VIBRATION

MAINTENANCE / SERVICE

ENVIRONMENT

• This tool is not intended for professional use

• Donotdisposeofelectrictools,batteries,

• Openingthehousingshellcandamageordestroy

accessoriesandpackagingtogetherwithhousehold

thetool

wastematerial (only for EU countries)

• Keep tool, charger and cutting blades clean

- in observance of European Directive 2002/96/EC on

! unplugchargerfrompowersourcebefore

waste of electric and electronic equipment and its

cleaning

implementation in accordance with national law,

- clean the tool with a damp cloth (do not use cleaning

electric tools that have reached the end of their life

agents or solvents)

must be collected separately and returned to an

- after use, always carefully clean and lightly lubricate

environmentally compatible recycling facility

the cutting blades

- symbol ! will remind you of this when the need for

! weargloveswhenhandlingorcleaningthe

disposing occurs

cuttingblades

! removethebatterybeforedisposalofthetool

• Regularly check the condition of the cutting blades and

• Removing/disposing of batteries )

the tightness of the blade bolts

! onlyremovethebatteriesiftheyarecompletely

• Regularly check for worn or damaged components and

empty

have them repaired/replaced when necessary

- protect battery terminals with heavy tape to prevent

• Sharpening the cutting blades

short-circuit

- remove cutting blades from tool before sharpening

- dispose of the battery at an ocial collection point for

- sharpen the cutting blades with a small and smooth

batteries

le, in case a solid object damaged them

! batteriesmayexplodewhendisposedofinfire,

- we advise you, however, to have the blades sharpened

sodonotburnbatteryforanyreason

by a specialist

- lubricate the cutting blades after sharpening

DECLARATION OF CONFORMITY

• Storage (

• We declare under our sole responsibility that the product

- store the tool indoors in a dry and locked-up place,

described under “Technical data” is in conformity with the

out of reach of children

following standards or standardization documents: EN

- securely mount storage rail L on the wall with 4 screws

60335, EN 60745, EN 61000, EN 55014 in accordance

(notsupplied) and horizontally leveled

with the provisions of the directives 2006/95/EC,

- use blade guards M 2 when storing the tool

2004/108/EC, 2006/42/EC, 2000/14/EC, 2011/65/EU

- lubricate the cutting blades before storing the tool

• Technicalfileat: SKIL Europe BV (PT-SEU/ENG1),

• If the tool/charger should fail despite the care taken in

4825 BD Breda, NL

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool or charger undismantled together with

proof of purchase to your dealer or the nearest SKIL

service station (addresses as well as the service

diagram of the tool are listed on www.skil.com)

- in case of a defective charger send bothchargerand

battery to your dealer or the SKIL service station

TROUBLESHOOTING

• The following listing shows problem symptoms, possible

causes and corrective actions (if these do not identify

and correct the problem, contact your dealer or service

station)

★ Tool operates intermittently

- internal wiring defective -> contact dealer/service

station

- on/o switch defective -> contact dealer/service

station

★ Motor runs but blades remain stationary

- internal fault -> contact dealer/service station

★ Cutting blades hot

- cutting blades blunt -> have blades sharpened

- cutting blades have dents -> have blades inspected

- too much friction due to lack of lubricant -> lubricate

blades

10

19.08.2013

11

NOISE/VIBRATION

• Measured in accordance with EN 60745 the sound

pressure level of this tool is 56 dB(A) and the sound

power level 76 dB(A) (standard deviation: 3 dB), and the

vibration <2.5 m/s² (hand-arm method; uncertainty K =

1.5 m/s²)

• Measured in accordance with 2000/14/EC (EN/ISO

3744) the guaranteed sound power level LWA is lower

than 79 dB(A) (conformity assessment procedure

according to Annex V)

• The vibration emission level has been measured in

accordance with a standardised test given in EN 60745; it

may be used to compare one tool with another and as a

preliminary assessment of exposure to vibration when

using the tool for the applications mentioned

- using the tool for dierent applications, or with dierent

or poorly maintained accessories, may signicantly

increase the exposure level