Gigabyte GA-8VM800PMD-775: Chapter 1 Hardware Installation
Chapter 1 Hardware Installation: Gigabyte GA-8VM800PMD-775
English
Chapter 1 Hardware Installation
1-1 Considerations Prior to Installation
Preparing Your Computer
The motherboard contains numerous delicate electronic circuits and components which can become
damaged as a result of electrostatic discharge (ESD). Thus, prior to installation, please follow the
instructions below:
1. Please turn off the computer and unplug its power cord.
2. When handling the motherboard, avoid touching any metal leads or connectors.
3. It is best to wear an electrostatic discharge (ESD) cuff when handling electronic components
(CPU, RAM).
4. Prior to installing the electronic components, please have these items on top of an antistatic pad or
within a electrostatic shielding container.
5. Please verify that the power supply is switched off before unplugging the power supply connector
from the motherboard.
Installation Notices
1. Prior to installation, please do not remove the stickers on the motherboard. These stickers are
required for warranty validation.
2. Prior to the installation of the motherboard or any hardware, please first carefully read the
information in the provided manual.
3. Before using the product, please verify that all cables and power connectors are connected.
4. To prevent damage to the motherboard, please do not allow screws to come in contact with the
motherboard circuit or its components.
5. Please make sure there are no leftover screws or metal components placed on the motherboard
or within the computer casing.
6. Please do not place the computer system on an uneven surface.
7. Turning on the computer power during the installation process can lead to damage to system
components as well as physical harm to the user.
8. If you are uncertain about any installation steps or have a problem related to the use of the product,
please consult a certified computer technician.
Instances of Non-Warranty
1. Damage due to natural disaster, accident or human cause.
2. Damage as a result of violating the conditions recommended in the user manual.
3. Damage due to improper installation.
4. Damage due to use of uncertified components.
5. Damage due to use exceeding the permitted parameters.
6. Product determined to be an unofficial Gigabyte product.
Hardware Installation- 9 -
1-2 Feature Summary
®
®
(Note 1)
CPU Supports LGA775 Intel
Pentium
4 Processor
L2 cache varies with CPU
English
Front Side Bus Supports 800/533MHz FSB
Chipset Northbridge: VIA P4M800 Pro Chipset
Southbridge: VIA 8237R+
LAN Onboard Realtek RTL8100C chip (10/100 Mbit)
Audio Onboard Realtek ALC655 chip
Supports 2 / 4 / 6 channel audio
Supports SPDIF In/Out connection
Storage VT8237R+ Southbridge
- 1 FDD connector, allowing connection of 2 FDD devices
- 2 IDE connectors (IDE1, IDE2) with UDMA 33/ATA 66/ATA 100/ATA 133
suppport, allowing connection of 4 IDE devices
- 2 SATA connectors (SATA0, SATA1), allowing connection of 2 SATA
devices
- Supports data striping (RAID 0), mirroring (RAID 1) for Serial ATA
O.S Support Microsoft Windows 2000/XP
(Note 2)
Memory 2 DDR II DIMM memory slots (supports up to 2 GB memory)
Supports DDR II 533/400 unbuffered DIMMs
Supports 1.8V DDR II DIMMs
Expanstion Slots 1 AGP slot
3 PCI slots
Internal Connectors 1 20-pin ATX power connector
1 4-pin ATX 12V power connector
1 floppy connector
2 IDE connectors
2 SATA connectors
1 CPU fan connector
1 system fan connector
1 front panel connector
1 front audio connector
1 CD In connector
1 AUX In connector
1 COMB connector
2 USB 2.0/1.1 connectors for additional 4 USB 2.0/1.1 ports by cables
1 SUR_CEN connector
1 SPDIF In/Out connector
1 power LED connector
GA-8VM800PMD-775 Motherboard - 10 -
Rear Panel I/O 1 PS/2 keyboard port
English
1 PS/2 mouse port
1 parallel port
1 serial port (COMA)
1 VGA port
4 USB 2.0/1.1 ports
1 RJ-45 port
3 audio jacks (Line In / Line Out / MIC In)
I/O Control Winbond W83627 chip
Hardware Monitor System voltage detection
CPU / System temperature detection
CPU / System fan speed detection
CPU / System fan failure warning
CPU smart fan control
BIOS 1 4Mbit flash ROM
Use of licensed AWARD BIOS
Additional Features Supports @BIOS
Supports Download Center
Supports Q-Flash
(Note 3)
Supports EasyTune (only supports Hardware Monitor function)
Supports Xpress Install
Supports Xpress Recovery
Supports Xpress Rescue
Bundle Software Norton Internet Security (OEM version)
Form Factor Micro ATX form factor; 24.4cm x 23.3cm
(Note 1) For further CPU support information, please go to GIGABYTE's website.
(Note 2) Use of a Double-Sided memory module (the single chip is 512 Mbit) is required if you wish to
install a 1 GB memory module.
(Note 3) EasyTune functions may vary depending on different motherboards.
Hardware Installation- 11 -
1-3 Installation of the CPU and Heatsink
Before installing the CPU, please comply with the following conditions:
English
1. Please make sure that the motherboard supports the CPU.
2. Please take note of the one indented corner of the CPU. If you install the CPU
in the wrong direction, the CPU will not insert properly. If this occurs, please change
the insert direction of the CPU.
3. Please add an even layer of heat sink paste between the CPU and heatsink.
4. Please make sure the heatsink is installed on the CPU prior to system use, otherwise
overheating and permanent damage of the CPU may occur.
5. Please set the CPU host frequency in accordance with the processor specifications. It is not
recommended that the system bus frequency be set beyond hardware specifications since it
does not meet the required standards for the peripherals. If you wish to set the frequency
beyond the proper specifications, please do so according to your hardware specifications
including the CPU, graphics card, memory, hard drive, etc.
HT functionality requirement content :
Enabling the functionality of Hyper-Threading Technology for your computer system requires all
of the following platform components:
®
®
- CPU: An Intel
Pentium
4 Processor with HT Technology
- Chipset: A VIA Chipset that supports HT Technology
- BIOS: A BIOS that supports HT Technology and has it enabled
- OS: An operation system that has optimizations for HT Technology
1-3-1 Installation of the CPU
Fig. 1
Fig. 2
Metal Lever
Gently lift the metal
Remove the plastic
lever located on the
covering on the CPU
CPU socket to the
socket.
upright position.
Fig. 3
Fig. 4
Notice the small gold
Once the CPU is prop-
colored triangle
erly inserted, please
located on the edge of
replace the load plate
the CPU socket.
and push the metal le-
Align the indented
ver back into its origi-
corner of the CPU with
nal position.
the triangle and gently insert the CPU into position.
(Grasping the CPU firmly between your thumb
and forefinger, carefully place it into the socket in a
straight and downwards motion. Avoid twisting or
bending motions that might cause damage to the
CPU during installation.)
GA-8VM800PMD-775 Motherboard - 12 -
English
1-3-2 Installation of the Heatsink
Male Push Pin
The top of Female Push Pin
Female Push Pin
Fig. 2
Fig.1
Please apply an even layer of heatsink paste on
(Turning the push pin along the direction of arrow
the surface of the installed CPU.
is to remove the heatsink, on the contrary, is to
install.)
Please note the direction of arrow sign on the male
push pin doesn't face inwards before installation.
(This instruction is only for Intel boxed fan)
Fig. 3
Fig. 4
Place the heatsink atop the CPU and make sure
Please make sure the Male and Female push pin
the push pins aim to the pin hole on the
are joined closely. (for detailed installation
motherboard.Pressing down the push pins
instructions, please refer to the heatsink installation
diagonally.
section of the user manual)
Fig. 6
Fig. 5
Finally, please attach the power connector of the
Please check the back of motherboard after
heatsink to the CPU fan header located on the
installing. If the push pin is inserted as the picture,
motherboard.
the installation is complete.
The heatsink may adhere to the CPU as a result of hardening of the heatsink paste.To prevent
such an occurrence, it is suggested that either thermal tape rather than heat sink paste be used
for heat dissipation or using extreme care when removing the heatsink.
Hardware Installation- 13 -
1-4 Installation of Memory
Before installing the memory modules, please comply with the following conditions:
1. Please make sure that the memory used is supported by the motherboard. It is
English
recommended that memory of similar capacity, specifications and brand be used.
2. Before installing or removing memory modules, please make sure that the computer
power is switched off to prevent hardware damage.
3. Memory modules have a foolproof insertion design. A memory module can be installed
in only one direction. If you are unable to insert the module, please switch the direction.
The motherboard supports DDR II memory modules, whereby BIOS will automatically detect memory
capacity and specifications. Memory modules are designed so that they can be inserted only in one
direction. The memory capacity used can differ with each slot.
Notch
DDR II
Fig.1
The DIMM socket has a notch, so the DIMM memory module
can only fit in one direction. Insert the DIMM memory module
vertically into the DIMM socket. Then push it down.
Fig.2
Close the plastic clip at both edges of the DIMM sockets to lock
the DIMM module.
Reverse the installation steps when you wish to remove the
DIMM module.
GA-8VM800PMD-775 Motherboard - 14 -
English
1-5 Installation of Expansion Cards
You can install your expansion card by following the steps outlined below:
1. Read the related expansion card's instruction document before installing the expansion card into
the computer.
2. Remove your computer's chassis cover, screws and slot bracket from the computer.
3. Press the expansion card firmly into expansion slot in motherboard.
4. Be sure the metal contacts on the card are indeed seated in the slot.
5. Replace the screw to secure the slot bracket of the expansion card.
6. Replace your computer's chassis cover.
7. Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS.
8. Install related driver from the operating system.
Installing a AGP expansion card:
Please carefully pull out the small white-
drawable bar at the end of the AGP slot
when you try to install/uninstall the VGA
card. Please align the VGA card to the
onboard AGP slot and press firmly down
on the slot. Make sure your VGA card is
locked by the small white-drawable bar.
Hardware Installation- 15 -
1-6 I/O Back Panel Introduction
English
PS/2 Keyboard and PS/2 Mouse Connector
To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard to the
lower port (purple).
Parallel Port
The parallel port allows connection of a printer, scanner and other peripheral devices.
Serial Port
Devices like mouses, modems, and etc. can be connected to Serial port.
VGA Port
Monitor can be connected to VGA port.
USB port
Before you connect your device(s) into USB connector(s), please make sure your device(s) such
as USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface. Also make
sure your OS supports USB controller. If your OS does not support USB controller, please contact
OS vendor for possible patch or driver upgrade. For more information please contact your OS or
device(s) vendors.
LAN Port
The provided Internet connection is fast Ethernet, providing data transfer speeds of 10/100Mbps.
Line In
Devices like CD-ROM, walkman etc. can be connected to Line In jack.
Line Out (Front Speaker Out)
Connect the stereo speakers, earphone or front surround channels to this connector.
MIC In
Microphone can be connected to MIC In jack.
GA-8VM800PMD-775 Motherboard - 16 -
English
1-7 Connectors Introduction
3
2
5
1
6
10
4
7
19
9
11
8
14 17 18
1513 1612
1) ATX_12V
11) CD_IN
2) ATX (Power Connector)
12) AUX_IN
3) CPU_FAN
13) SPDIF_IO
4) SYS_FAN
14) SUR_CEN
5) FDD
15) F_USB1 / F_USB2
6) IDE1 / IDE2
16) COMB
7) SATA0 / SATA1
17) CI
8) F_PANEL
18) CLR_CMOS
9) PWR_LED
19) BATTERY
10) F_AUDIO
Hardware Installation- 17 -
1/2) ATX_12V / ATX (Power Connector)
With the use of the power connector, the power supply can supply enough stable power to all
the components on the motherboard. Before connecting the power connector, please make sure
that all components and devices are properly installed. Align the power connector with its
English
proper location on the motherboard and connect tightly.
The ATX_12V power connector mainly supplies power to the CPU. If the ATX_12V power
connector is not connected, the system will not start.
Caution!
Please use a power supply that is able to handle the system voltage requirements. It is
recommended that a power supply that can withstand high power consumption be used (300W
or greater). If a power supply is used that does not provide the required power, the result can
lead to an unstable system or a system that is unable to start.
Pin No. Definition
4
2
1 GND
2 GND
3
1
3 +12V
4 +12V
Pin No. Definition
1 3.3V
2 3.3V
11
1
3 GND
4 +5V
5 GND
6 +5V
7 GND
8 Power Good
9 5V SB (stand by +5V)
10 +12V
11 3.3V
12 -12V
20
10
13 GND
14 PS_ON(soft on/off)
15 GND
16 GND
17 GND
18 -5V
19 +5V
20 +5V
GA-8VM800PMD-775 Motherboard - 18 -
3/4) CPU_FAN / SYS_FAN (Cooler Fan Power Connector)
English
The cooler fan power connector supplies a +12V power voltage via a 3-pin/4-pin (only for
CPU_FAN) power connector and possesses a fool-proof connection design.
Most coolers are designed with color-coded power connector wires. A red power connector
wire indicates a positive connection and requires a +12V power voltage. The black connector
wire is the ground wire (GND).
Please remember to connect the power to the cooler to prevent system overheating and
failure.
Caution! Please remember to connect the power to the CPU fan to prevent CPU overheating
and failure.
1
Pin No. Definition
1 GND
CPU_FAN
2 +12V
3 Sense
4 Speed Control
1
(Only for CPU_FAN)
SYS_FAN
5) FDD (FDD Connector)
The FDD connector is used to connect the FDD cable while the other end of the cable connects to the
FDD drive. The types of FDD drives supported are: 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB.
Please connect the red power connector wire to the pin1 position.
34
33
2
1
Hardware Installation- 19 -
6) IDE1 / IDE2 (IDE Connector)
An IDE device connects to the computer via an IDE connector. One IDE connector can connect to
one IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical
drive). If you wish to connect two IDE devices, please set the jumper on one IDE device as Master
English
and the other as Slave (for information on settings, please refer to the instructions located on the IDE
device).
40
39
2
1
IDE1
IDE2
7) SATA0 / SATA1 (Serial ATA Connector)
Serial ATA can provide up to 150MB/s transfer rate. Please refer to the BIOS setting for the Serial
ATA and install the proper driver in order to work properly.
Pin No. Definition
1 GND
1
7
2 TXP
3 TXN
4 GND
5 RXN
6 RXP
7 GND
GA-8VM800PMD-775 Motherboard - 20 -
8) F_PANEL (Front Panel Connector)
English
Please connect the power LED, PC speaker, reset switch and power switch etc. of your chassis
front panel to the F_PANEL connector according to the pin assignments below.
Speaker Connector
Message LED/
Power/
Power
Sleep LED
Switch
PW+
MSG+
MSG-
PW-
SPEAK+
SPEAK-
2
20
1
19
HD-
RES+
NC
HD+
RES-
Reset Switch
IDE Hard Disk Active LED
HD (IDE Hard Disk Active LED) Pin 1: LED anode(+)
Pin 2: LED cathode(-)
SPEAK (Speaker Connector) Pin 1: Power
Pin 2- Pin 3: NC
Pin 4: Data(-)
RES (Reset Switch) Open: Normal
Close: Reset Hardware System
PW (Power Switch) Open: Normal
Close: Power On/Off
MSG (Message LED/Power/Sleep LED) Pin 1: LED anode(+)
Pin 2: LED cathode(-)
NC NC
Hardware Installation- 21 -
9) PWR_LED
PWR_LED is connected with the system power indicator to indicate whether the system is on/off.
It will blink when the system enters suspend mode.
English
1
Pin No. Definition
1 MPD+
2 MPD-
3 MPD-
10) F_AUDIO (Front Audio Panel Connector)
Please make sure the pin assignment on the cable is the same as the pin assigment on the MB
header. To find out if the chassis you are buying support front audio panel connector, please
contact your dealer. If you want to use "Front Audio" connector, you must remove the jumpers
from pins 5-6, 9-10.
Pin No. Definition
1 MIC
10
9
2 GND
3 MIC_BIAS
2
1
4 POWER
5 FrontAudio(R)
6 Rear Audio (R)/ Return R
7NC
8 No Pin
9 FrontAudio (L)
10 Rear Audio (L)/ Return L
GA-8VM800PMD-775 Motherboard - 22 -
11) CD_IN (CD IN Connector, black)
English
Connect CD-ROM or DVD-ROM audio out to the connector.
Pin No. Definition
1 CD-L
2 GND
1
3 GND
4 CD-R
12) AUX_IN (AUX In Connector, white)
Connect other device (such as PCI TV Tunner audio out) to the connector.
Pin No. Definition
1 AUX-L
1
2 GND
3 GND
4 AUX-R
Hardware Installation- 23 -
13) SPDIF_IO (SPDIF In/ Out connector, red)
The SPDIF output is capable of providing digital audio to external speakers or compressed AC3
data to an external Dolby Digital Decoder. Use this feature only when your stereo system has
digital input function. Use SPDIF IN feature only when your device has digital output function.
English
Be careful with the polarity of the SPDIF_IO connector. Check the pin assignment carefully while
you connect the SPDIF cable. Incorrect connection between the cable and connector will make the
device unable to work or even damage it. For optional SPDIF cable, please contact your local
dealer.
Pin No. Definition
1 Power
62
2 No Pin
3 SPDIF
1
5
4 SPDIFI
5 GND
6 GND
14) SUR_CEN (Surround Center Connector, black)
Please contact your nearest dealer for optional SUR_CEN cable.
Pin No. Definition
2
6
1 SUR OUTL
2 SUR OUTR
3 GND
1
5
4 No Pin
5 CENTER_OUT
6 BASS_OUT
GA-8VM800PMD-775 Motherboard - 24 -
15) F1_USB / F2_USB (Front USB Connectors)
English
Be careful with the polarity of the front USB connector. Check the pin assignment carefully while
you connect the front USB cable, incorrect connection between the cable and connector will make
the device unable to work or even damage it. For optional front USB cable, please contact your
local dealer.
Pin No. Definition
2
10
1 Power(5V)
2 Power(5V)
1
9
3 USB0 DX-
4 USB1 Dy-
5 USB0 DX+
6 USB1 Dy+
7 GND
8 GND
9 No Pin
10 NC
16) COMB (COMB Connector)
Be careful with the polarity of the COMB connector. Check the pin assignments while you connect
the COMB cable. Please contact your nearest dealer for optional COMB cable.
Pin No. Definition
1 NDCDB-
2
10
2 NSINB
3 NSOUTB
1
9
4 NDTRB-
5 GND
6 NDSRB-
7 NRTSB-
8 NCTSB-
9 NRIB-
10 No Pin
Hardware Installation- 25 -
17) CI (Chassis Intrusion, Case Open)
This 2-pin connector allows your system to detect if the chassis cover is removed. You can check
the "Case Opened" status in BIOS Setup.
English
Pin No. Definition
1 GND
2 Signal
1
18) CLR_CMOS (Clear CMOS)
You may clear the CMOS data to its default values by this jumper. To clear CMOS, temporarily
short pins 1-2. To prevent improper use of this header, we do not include a jumper on it.
Open: Normal
1
Short: Clear CMOS
1
GA-8VM800PMD-775 Motherboard - 26 -
19) BATTERY
English
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's
instructions.
If you want to erase CMOS...
1. Turn OFF the computer and unplug the power cord.
2. Take out the battery gently and put it aside for about 10 minutes
(Or you can use a metal object to connect the positive and
negative pins in the battery holder to make them short for one
minute).
3. Re-install the battery.
4. Plug the power cord and turn ON the computer.
Hardware Installation- 27 -
English
GA-8VM800PMD-775 Motherboard - 28 -
Оглавление
- GA-8VM800PMD-775 Motherboard Layout
- Block Diagram
- Chapter 1 Hardware Installation
- Chapter 2 BIOS Setup
- Chapter 3Drivers Installation
- Chapter 4 Appendix
